LumberJocks

flcopper169's Favorites

  • Advertise with us
View degoose's profile

David's [aka Patron] double curve..my version of the jig? #3: Just kidding!

06-13-2009 01:05 PM by degoose | 8 comments »

Basic 1/4 ” plywood.. mark a line at a diagonal across the board.NB. the sharper the angle the longer the piece that can be cut.Inset two bearings on this line 19” on centre to enable the use of the 9.5” Radius template from the first jig with single curve. Fit a bolt in the righthand bearing and fit to the bearing in the base unit.. turn on bandsaw and cut the curve till you reach the line and then change pivot points to the left hand side of both the jig and the base unit ...

Read this entry »


View degoose's profile

Spirals #1: How to make the "Spiral Lazy Larry"

06-01-2009 06:52 AM by degoose | 23 comments »

You will need 12 pieces of timber roughly 5’’ by 12’’ whatever thickness you want. [ I milled mine to 5/8”]The first one I made was PH and SA—6 of each.Place timber in the jig and cut the first arc.Move the piece into the fence, clamp and make the second arc cut. Repeat 12 times.Glue it up and cut it into a circle.Put on a little tung oil finishThats about It.

Read this entry »


View degoose's profile

Spirals #3: Making the individual parts.

06-01-2009 08:48 AM by degoose | 11 comments »

The base is just 1/4 inch ply. any size is ok..I have a cirlce cutting jig [ a jig makes it easier]..see circle cutting blog Drill a hole in the ply to use as pivot point The distance from the centre of the pivot to the blade is 9.5 inches Set this distance and cut an arc across the end of the ply.The fence is made by making one cut at the same 9.5” distance and then drilling another hole back an inch or so.[don’t move the jig!]. not really exact but enough to be able to drill...

Read this entry »


View degoose's profile

Spirals #4: Assembling the jig

06-01-2009 09:03 AM by degoose | 30 comments »

Drill two holes in the fence . one a little larger.. to take 1/4 ” bolts . Mark these positions on the base and drill these holes to attach the fence to the base. One bolt is held with a nut and other with a Knob.[for adjustment in fine tuning the fence if necessary]. Drill two addition holes in the fence to accept 1/4 ” bolts for tightening the bridge clamps.[These holes got through the fence only] Refer to the photo.In his pic you may see that I inserted a bearing to serve as...

Read this entry »


View degoose's profile

Spirals #5: A quick sneak peak of some new timber combos

06-02-2009 10:16 AM by degoose | 19 comments »

Just a quick peak at what I got up to today when I was not checking the hundreds of emails from all the LJs who commented on my last few posts.. Thank you very much.. I did not realize how much of my daily routine now revolves around this site.. Addictive…I also had time to drive the twenty odd miles into the big smoke..Brisbane and go shopping at Carba-tec..I know I have all the fun..A coupla new router bits..some very expensive toggle clamps [for a new jig to make the sunburst design...

Read this entry »


View scrappy's profile

Making A Segmented Ring Without A Lathe / A Step by Step Tutorial

06-07-2009 09:15 PM by scrappy | 36 comments »

Well, I was asked to put together a blog on how I made my segmentd ring. Since I had to make a new one for myself, (first one too small) I thought I would go ahead and do a step by step picture tutorial. My first time ever doing something like this , so hope it comes out OK. Here goes; Wood Selection The first step in making the ring is deciding what woods to use. As we all know, the selection is quite large. One of the most important things is color, but the most important is hardne...

Read this entry »


View degoose's profile

Spirals #6: We are not finished yet.

06-03-2009 02:23 AM by degoose | 18 comments »

Next step is to make the ends of the segments curved. Shell-like if you want.For that we need a new jig.. Yeah I know some of you haven’t finished the first one..!This is ultra simple.Firstly a fresh piece of ply .. 1/4 ” is fine.I inserted a bearing to make this more durable .. same same as last one.This was positioned 4.5 ” from the end[centred on the width] and an arc cut on the end via the circle cutting jig.. same same.Cut two fences same as the one of the first jig &#...

Read this entry »


View degoose's profile

Glue up of a woven board..

05-17-2009 10:31 AM by degoose | 19 comments »

This is just a little tip.. not the whole tutorial of how to cut and make a woven board.Basically you all can make the weave with the two accent stripes on each side.. right.[ ok just a length of the main timber with 2 stripes cut 1/16 or 1/8 ” thick and glued up. see the pics and work it out ]You can also make the background pieces from the other of the accent timbers the same width as the main weave less the accents.. ok so far.. so I don’t need to go though all that do I? PM m...

Read this entry »


View Todd A. Clippinger's profile

Shop Skills #2: Card Scrapers the Video!

12-29-2008 03:43 AM by Todd A. Clippinger | 54 comments »

It’s Finally Here! I have completed my first feature woodworking video. This video shows how I sharpen my card scrapers. It is a simple process and I kept the instruction simple with some close-up video action. I hope this post goes smooth, it has taken me all day to figure out how to finish up the video and 3 attempts to get it online. So this is a pretty big moment. I can work on polished video later but I have to start somewhere. I hope that this video on sharpening ca...

Read this entry »


View dewoodwork's profile

Beautiful end grain cutting boards free project plan

11-25-2007 07:31 AM by dewoodwork | 97 comments »

Construct these beautiful end grainCutting boards Hello fellow woodworkers,In the spirit of sharing woodworking knowledge I am writing this tutorial for anyone interested in constructing these beautiful end grain cutting boards. Take a look at the photos of the four styles I have made, or create your own pattern’s and follow the steps I have outlined in this tutorial. Questions and comments are welcome, enjoy. For this board I used maple, walnut, lyptus and purpleheart. White oak, wa...

Read this entry »


1 2 next »
11 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com