Difficult is Just Easy Work Done Slowly

  • Advertise with us
Blog entry by duongtd1102 posted 12-20-2015 02:40 AM 995 reads 0 times favorited 4 comments Add to Favorites Watch

What was the last difficult moment you had with a project? Was it a particularly complex joint or a nasty bit of figured grain? How did you tackle it? I bet the solution regardless of the tools being used was to slow down and take care of it meticulously. If you think about it, “difficult” tasks just force us to slow down. Sometimes to glacial speeds.
So when you look at it that way, no project is really that hard to make, but rather just slower.
Its quite liberating!

I’m a firm believer that any woodworker of any skill level should feel free to tackle any project that strikes their fancy. Woodworking is just a series of individual tasks, often repeated many many times. Break down those tasks far enough and you will see just how simple a project can be. For that matter the tools we use to do those tasks play a major role in how “difficult” it is to accomplish.
plowing with a t&g planeConsider the humble groove for, say, a drawer bottom. Cut with a hand held router and a bearing guided bit and this is fast and easy. The slow bit is in setting the bit height and securing the work piece. Now drop that router into a table with a lift and the groove becomes even easier (faster). On the non powered front, using a plow plane is just as easy. Set the fence and depth stop and the joint is a cinch. But take away the plow plane and hand the woodworker just a chisel. Funny how “difficult” that simple groove is now. But the act of using a chisel to chop out a groove is as simple and easy as can be, but you have to go slowly and meticulously lay out the extents of the groove and be careful of taking to heavy a bite with the chisel while ensuring you maintain an equal depth. There are a lot of variables to keep track off that we relied on fences and depth stops and bearings with other tools.
Its the same joint but each method discussed above takes different amounts of time and can therefore be perceived as more difficult than another.
Now I have cut grooves using all of these methods (plus a few more) and one quickly learns that this “difficult” joint can be made easier by bringing to bear a different tool. But that’s not always the case. Whether because the best tool is cost prohibitive or just so specific as to not be logical for a unique situation. But there are also times when no matter what tool you throw at the problem, it won’t speed things up. These tasks are the truly difficult ones that scare many a woodworker away.

My first Ball & Claw footFor me it was the ball and claw foot. There were several lovely furniture pieces I wanted to build but they all included the ball and claw foot. I loved this detail and didn’t want to skip it so I seemed to have no option but to either cower in fear or suck it up and learn to carve this detail.
My first example took me about 5 hours but when finished it looked really good. I would not have hesitated to use it in a project. There was no way to speed this up other than make some more and to get more comfortable with the steps and with the carving gouges. But as evidenced by the respectable appearance of my first foot, it wasn’t hard at all, just slow.
Hopefully you are starting to see what I’m talking about and perhaps that bucket list project of yours went from scary and difficult to something that you just need to slow down and get done.
Your Turn
Name a difficult woodworking task that has you stumped. I bet we can figure out an easy way to do it slowly.
how i get paid to travel the worldreverse osmosis water filtration system reviews

-- "water filter reviews ":

4 comments so far

View Richard H's profile

Richard H

490 posts in 2284 days

#1 posted 12-20-2015 02:58 PM

View schugi's profile


50 posts in 1842 days

#2 posted 12-25-2015 03:57 AM

Thank you for this. It was really nicely expressed. Its funny but often times when you slow down and do things the right way, you end up saving time in the long run. Patience can be hard tho.

-- Chuck, Minnesota

View WoodNSawdust's profile


1417 posts in 1780 days

#3 posted 12-25-2015 06:08 PM

I used to be of the opinion that anyone could learn to do anything. Then I met a woman who wanted to change careers and become a computer technician. It took forever to teach her which way to turn a screwdriver. She could never learn how to look at a threaded hole and pick a bolt that would fit. After many service calls where she would try to muscle a #6 bolt into a #4 hole and it would seize I had to let her go. My conclusion is that there are some people who cannot learn something.

For woodworking I hold to the incremental approach. Most projects should be slightly more difficult and should help the woodworker expand their abilities. But, if a beginner tackles an extremely difficult project they will fail and this will affect their confidence.

-- "I love it when a plan comes together" John "Hannibal" Smith

View duongtd1102's profile


5 posts in 1494 days

#4 posted 05-16-2016 04:55 PM

@WoodNSawdust Thankyou man

- -

MineCraft unblocked at Unblocked Game at school

-- "water filter reviews ":

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics