LumberJocks Woodworking Forum banner
26K views 72 replies 31 participants last post by  Ken90712 
#1 ·
Initial thoughts.

Have been thinking for some time to try my hand at a sushi board.. was in town today and picked up some small dishes… suitable for dipping sauce… so I have laminated a strip of Purple Heart between some boards of Queensland Maple…[ not a true maple… it is a flindersia not an acer]

Any way waiting for the glue to dry again…

No pics yet.. so stay tuned..
 
#7 ·
A blank and two bowls...

Here is the blank of maple and purple heart… remember this is Queensland Maple and not the maple you get maple syrup from…

I have two dipping bowls and I am not sure which one will be right for the Sushi Board…

Number one is square sided and deeper…


Number two is divided into two sections and has rounded corners but is shallow..


I intend to curve the ends and using dowels attach the curved handles … maybe purple heart…

What do you think?
 
#8 ·
I am no sushi aficionado but I think the square one works better for spilling purposes. Neat board, oh master board maker! I'll be interested to see how fast they sell in your parts. Here on Cape Cod, they go like hotcakes… Or fishcakes!!!
Ellen
 
#18 ·
Two in a set.

I thought that a maching set of two sushi boards would be nice.

After selecting a nice board of Queensland Maple… I cut 2 blanks…and then using the curve cutting jig on the bandsaw …. I cut an asymmetrical curve across each board.


2 stipes of Purple Heart and 1 stripe of Camphor Laurel were captured and glued between the two halves.


A few hours in clamps.


And then the whole lot were sanded and the ends cut..


More on how the ends were cut and how the handles were made… next time..a set of four…. until then thanks for dropping by..
 
#25 ·
Two handles, two curves..

You will have seen on the sushi boards, that I have cut two curves on the handles.. If I were just making one board, the cuts could be made freehand on the bandsaw…but…

Since this is now part of the range… I need to be able to produce these cuts on a regular and repeatable basis… so once more a jig is needed..

To start, glue the mainboard to the handle/ends… this need not be a great bond… it is to temporarily hold the pieces together while they are cut…


Move to the bandsaw and make the first of a series of cuts..


The handle is cut… on the curve cutting jig,


The blank is then moved along the jig and the cut is repeated to remove the waste of the handle.


Using a small amount of glue the cut handle is glued onto a scrap [remembering to position the piece curve side up and the holes outward.]... for easier handling on the curve cutting jig.


You may see the holes for the brass rods have already been drilled..

A fence was set up and positioning marks made on the fence.


Now we repeat the cuts for the second curve on the handles.




You will notice that there were two sets of holes drilled in this piece… a small mistake that will be easily fixed with a little sanding…


Here be the four blanks for the set of four..

Queensland Maple with one thin stripe of Purple Heart…

More to come!
 
#26 ·
Soooo, that's the method to your madness, heh, Larry? Thank you for sharing how you do it with us! That's one of the reasons I like LJ so much. I am constantly learning and having fun at the same time! Y'just can't beat that! Don't stop, y'hear? ! ? ! ? !
 
#30 ·
Out of order... sorry....

I have been busy as you can see… the sushi board series is coming along swimmingly…

I took a few pics to show you some of the steps…


Here are the various steps..

1. Glue two boards of Qld. Maple with a strip of Purple Heart in the middle…


2.Glue the ends temporarily.


3. Cut handles from ends and shape the main board.

more previously…...
 
#36 ·
Coming together

Nearly there.


Just a few shot to show the progress.. and to give you all an idea how they might look…


Still of two minds with the bowls…


Leaning towards the rounded on at an angle in line with the striping..
 
#48 ·
Setting the bowl into the board..

The divided bowl won hands down… so now to inlay or recess the bowl into the tray so that is does not move around..


Using the Torque WorkCentre, I set the limit stops on the x and y axies, and routered a square hollow shape in some MDF..bit hard to see here… but trust me…


This is the shape that will be routered onto the Sushi board..


The template is then turned over and setting the router above a pin in the table, the outer shape is etched on the board..See the stainless steel pin??
This etching will allow me to see where the cutter will be following the pin…


Two fences were added to capture the board and help with alignment.. two toggle clamps were added to secure the sushi board to the jig…

What another jig… I just love jigs…


The square was routed in 3 passes… using the in-built depth stop…


We are certainly moving along…


All four boards were routered in a matter of minutes.. all exactly the same…


Again with the mineral spirits, to showcase the colour and grain..

I hope I am not overloading you with this build… but I have so much to accomplish, I must move fast…
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top