LumberJocks

Woodworking blog entries tagged with 'windmill'

  • Advertise with us
View JobK's profile

Spinnekop (windmill) #9: Korbelen

11-01-2020 06:47 PM by JobK | 0 comments »

With the posts and the girders made, its time to make the “korbelen”. These knee braces help strengthen the construction of the lower part of the windmill and prevent it from skewing. Cutting the angles on the knee braces Making the tenons Making the mortise Joining it all together Fitting the pieces It fits!! The progress so far

Read this entry »


View JobK's profile

Spinnekop (windmill) #7: Fitting the parts together

10-25-2020 11:02 AM by JobK | 0 comments »

Just some pictures of putting all the parts together Lower end of the post fitting the “onder tafelment” Top end of the post and the “boven tafelment” Numbering the pieces Finished so far.

Read this entry »


View JobK's profile

Spinnekop (windmill) #6: De pannenkoek

10-25-2020 10:54 AM by JobK | 2 comments »

At the top of the lower house of this windmill there is a round flat part where the top of the windmill rests on and that makes it able to smoothly turn the upper part of the windmill into the wind. The part is called “de pannenkoek”, the pancake.The pancake consists of 4 parts that are lap jointed together Gluing the pieces together. In need of some sanding The finished products so far. 

Read this entry »


View JobK's profile

Spinnekop (windmill) #5: De achtakant stijlen

09-27-2020 11:24 AM by JobK | 2 comments »

Having finished the “onder tafelment” and the “boven tafelment”, now I will make the posts, and because the shape of the underside of this windmill is octagonal (in most cases it is a square ) these part are called octagon posts (achtkant stijlen) To make all the angled and compound cuts I first made a jig Making the jig Cutting all posts to length Cutting the tenons at the bottom of the posts Cutting the tenons at the top of the posts

Read this entry »


View JobK's profile

Spinnekop (windmill) #4: De koker

09-27-2020 11:18 AM by JobK | 3 comments »

This part of the mill is called “koker” and can be translated as tube. It is part of the bottom part of the windmill and allows the main drive shaft to go from the upper part to the lower part. It also allows the top of the windmill to be turned to face the wind with its wings faced in that direction. It is made of 8 pieces and is held together by the “boven tafelment” and some iron bands. On the drawing are some comments noting that the tube has been replaced at the wrong dimen...

Read this entry »


View JobK's profile

Spinnekop (windmill) #3: Boven tafelment

08-29-2020 02:16 PM by JobK | 0 comments »

In the previous blog a made the “onder tafelment”, now I am going to make the “boven tafelment” (onder is under and boven is upper). It is located at the top of the underpart of the windmill. It is made up of 4 pieces and has lap joints. There are also mortises in these pieces where the post of the lower house will sit. Starting with these piece Making the lap joints Fitting it together. After making the mortises Now I realized that I needed mortises in the “onder tafel...

Read this entry »


View JobK's profile

Spinnekop (windmill) #2: Onder tafelment

08-29-2020 02:08 PM by JobK | 1 comment »

The first thing to build is the base of the underpart of the windmill. It is made up of 8 pieces with lapjoints to make a octagon. It is called the ”onder (under) tafelment” The windmill was made off oak and I will use the same material. After making some strips of 15 by 6.5 mm I made the lap joints on the table saw And so I finished the “onder tafelment” 

Read this entry »


View JobK's profile

Spinnekop (windmill) #1: Preparations

08-29-2020 02:01 PM by JobK | 2 comments »

Preparations After building a new woodworking workshop last year I was searching for a new project to build.Being a miller (voluntarily, hobby at Deelmolen or Grevensmolen) and after building a small windmill before.I wanted a new challenge. So I went on the internet looking for some nice drawings of a windmill I could make in miniature.And so I stumbled op un these drawings (sheet 1) and sheet 2) After doing some research I also found some old pictures of the now demolish windmill (bac...

Read this entry »


View frank's profile

"Good Things Happen" by RusticWoodArt

07-20-2007 01:40 PM by frank | 5 comments »

Good Things Happen Today I am going to vary my blog style some what and pass the morning’s sun highlight on to an-other worker of wood….and also a worker in many fields of yet to come. A dreamer of sorts, who has chosen to put his hands into the multi-tasking of what can I do to better not only my situation, my families outcome and then also what can I do for my village or community….today this is where this young man is, tomorrow will yet come when he looks forth upon th...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com