LumberJocks

Woodworking blog entries tagged with 'stickley'

  • Advertise with us
View pintodeluxe's profile

Stickley / Jeff Jewitt Arts and Crafts Finish

04-15-2013 01:24 AM by pintodeluxe | 14 comments »

I wanted to recreate this Jeff Jewitt finish from Fine Woodworking #157, however the article didn’t list which formula was used. I consulted with Jeff, and it was Transtint Brown Mohogany dye, followed by McCloskeys Walnut stain. McClosky no longer makes stain, but sold to Valspar / Cabot. ---So I set out to make a sample board to achieve the rich, dark color I was after. ---The top colors are stain only, the middle colors are dye first then stain, and the bottom color is dye only. ...

Read this entry »


View pintodeluxe's profile

Stickley #369 Morris Chair #6: Leather Upholstery

03-24-2014 11:12 PM by pintodeluxe | 33 comments »

I took a leather sewing class to learn how to make the Morris chair cushions. -----The seat cushion and the ottoman cushion require web frames. Here I am milling the half-lap components for the web frames. -----Web frame assemblies are glued together. The seat frame should be sized 1/4” smaller in all directions than the opening in your chair, to allow room for the leather and two layers of batting.-----Corner blocks are added to the large seat cushion for additional strength. -----I...

Read this entry »


View pintodeluxe's profile

Stickley #369 Morris Chair #1: Leg Laminations and Angled Tenons

02-24-2014 09:27 PM by pintodeluxe | 6 comments »

Here is the project at hand, a slant arm Morris Chair. I am working off plans from the Popular Woodworking April 2011 issue, which I recommend you buy. The Author is Robert Lang. He posted a free diagram to Sketchup, but with this detailed of a project, you will want to order the back issue. My techniques differ from Robert’s methods significantly, so I will try to elaborate along the way. -----I like to start by laminating the legs for quartersawn figure on all four sides. ...

Read this entry »


View pintodeluxe's profile

Arts and Crafts Wedge and Strap Bed #1: Laminated Posts

07-16-2013 07:34 PM by pintodeluxe | 9 comments »

This is the queen size bed that I am building. Material is quartersawn red oak. -----I started with some veneers for the legs. I resawed some 3/4” stock at the bandsaw, and planed them to thickness. Then I wrapped them with some shrink wrap to keep them flat. ----- The veneers are slightly oversized, and 1/4” thick. Although the finished veneers will be only 3/32” thick, I leave them thicker because 1) they are easier to glue up, and 2) they come out of the planer lo...

Read this entry »


View CampD's profile

Vintage Mission/Arts & Crafts style finishing technique on White Oak

01-30-2016 03:11 PM by CampD | 8 comments »

There was quite the interest in the finishing process I used on my Stickley styled TV stand. http://lumberjocks.com/projects/217866I really only just gave the cliff notes version in its description. So with this blog, I’ll give the full detailed process I used to achieve that finish. It’s a time consuming process, more like it takes little time each day, but rather is spread out over numerous days. This process is not for those who feel the need to just get it assembled! Don’t fear, I worked ...

Read this entry »


View pintodeluxe's profile

Arts and Crafts 6 Drawer Dresser #11: Waxing Dressers and adding Drawer Pulls

02-04-2013 05:30 PM by pintodeluxe | 8 comments »

I waxed the dressers with Howards Walnut wax and #0000 steel wool. I tested the difference between sanding with a 1500 grit sanding sponge, and waxing with steel wool – and I prefered the latter. I waxed with the grain, and let the wax dry. Then I buffed it off with a clean lint-free rag. ----- For drawer pull layout I used Scott Collins no-math layout method. My drawer pulls have 2 bolts, 3” on center. -----I made a full-height jig to drill the holes for the machine bo...

Read this entry »


View pintodeluxe's profile

Cherry Refreshment Table #1: Breadboard Ends and Tusk Tenons

02-02-2014 06:40 AM by pintodeluxe | 10 comments »

Here is my cherry refreshment table which will feature a single drawer and breadboard ends.-----I started by making breadboard mortises at the router table. The mortises are 1-1/4” deep and cut in multiple shallow passes. -----I used a 1/4” spiral bit to center a 3/8” groove in the breadboard ends. I made an initial pass in the standard right to left direction. Then I flipped the board end for end and made a pass from left to right to avoid a climb cut.-----I set up my t...

Read this entry »


View brianl's profile

Finishing #1: Finding a stickley finish

05-12-2010 05:25 AM by brianl | 6 comments »

I have been working on a pair of nightstands for a while now and I’ve been trying to sort out what stain to use on them. They are quartersawn white oak and reproduction Stickleys so I wanted a nice older look. I started digging around in magazines, books, online, etc… and I found some great resources – like Captain Skully's forum post. Unfortunately, viewing something over the net always makes it appear a bit “off” to me. So I decided that I needed to prototy...

Read this entry »


View pintodeluxe's profile

Arts and Crafts 6 Drawer Dresser #7: Clamshell Biscuits, And Building a Flat Top Panel

01-07-2013 06:39 PM by pintodeluxe | 3 comments »

Here is the plan from my design. It incorporates some Stickley design elements. --The dresser carcases are assembled, including the small divider that separates the top two drawers.--The small dividers are attached with biscuits. To cut the slots, I opened the top two web frames like a clamshell. The web frames were aligned, and clamped together. Then I added an Emerson straightedge clamp, positioned to center the small divider on the web frame. --The ruler on the Emerson clamp helps cen...

Read this entry »


View pintodeluxe's profile

Arts and Crafts Nightstand #1: Side panels and Arched Lower Rail

05-17-2013 09:44 PM by pintodeluxe | 9 comments »

Here is a sketch of the nightstand I am working on. It features one 6” over two 8” drawers. -----Side panel components have been sanded, and the solid panels pre-stained. Now a final test fitting before gluing them up. The lumber is QSRO.-----A shallow groove in the legs will receive corbels. -----Side panels glued up. -----Front lower rails have been shaped at the router table, and finish sanded. Next up is the back panel and web frames.

Read this entry »


1 2 3 4 ... 14 next »
133 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com