LumberJocks

Woodworking blog entries tagged with 'stickley'

  • Advertise with us
View pintodeluxe's profile (online now)

Stickley #369 Morris Chair #3: Slant Arms and Side Slats

03-03-2014 08:08 PM by pintodeluxe | 4 comments »

This is how the Morris chair looks at this stage.-----I wanted to drill all the 5/8” holes for the backrest assembly before the glueup. It seems like this step would be easy to forget, so I’ll take care of it now. -----There are a lot of odds and ends to take care of before glueup, including easing edges of the parts at the router table. -----Now the side assembly can be dry fit. -----Note that the angled top side rails are 1/4” taller than the shoulders of the leg tenon...

Read this entry »


View pintodeluxe's profile (online now)

Stickley #369 Morris Chair #2: Frame Assembly and Through Tenons

02-28-2014 06:28 PM by pintodeluxe | 10 comments »

Here is where the project is at currently.-----Before I angle the top side rails, I mark the height of the small tenon.-----Then I trim away the excess tenon at the bandsaw. -----Fitting the small tenon into the back leg mortises. -----The joint looks a little peculiar at this point because the top rails have not been angled yet. -----With the frame dry fit I can measure the height of the side slats. -----With the repeater set up on my miter saw, I cut the 10 slats to the same length. --...

Read this entry »


View pintodeluxe's profile (online now)

Stickley #369 Morris Chair #1: Leg Laminations and Angled Tenons

02-24-2014 09:27 PM by pintodeluxe | 6 comments »

Here is the project at hand, a slant arm Morris Chair. I am working off plans from the Popular Woodworking April 2011 issue, which I recommend you buy. The Author is Robert Lang. He posted a free diagram to Sketchup, but with this detailed of a project, you will want to order the back issue. My techniques differ from Robert’s methods significantly, so I will try to elaborate along the way. -----I like to start by laminating the legs for quartersawn figure on all four sides. ...

Read this entry »


View Nels's profile

How to make hand made curved surfaces look good in a chair bottom

02-10-2014 01:41 PM by Nels | 10 comments »

When I started out working with wood, it was a chore to find any information. I went to used book stores and bought anything that might help and asked any woodworkers I knew. Then Fine Woodworking came along and now the internet. Lumberjocks is the best help I’ve found. There are always several guys who have gone through the same problem.Now, I’m working on 15 chairs. There have been three difficult parts. The curved back, the back legs, and the chair bottom. I’m curre...

Read this entry »


View pintodeluxe's profile (online now)

Cherry Refreshment Table #1: Breadboard Ends and Tusk Tenons

02-02-2014 06:40 AM by pintodeluxe | 10 comments »

Here is my cherry refreshment table which will feature a single drawer and breadboard ends.-----I started by making breadboard mortises at the router table. The mortises are 1-1/4” deep and cut in multiple shallow passes. -----I used a 1/4” spiral bit to center a 3/8” groove in the breadboard ends. I made an initial pass in the standard right to left direction. Then I flipped the board end for end and made a pass from left to right to avoid a climb cut.-----I set up my t...

Read this entry »


View pintodeluxe's profile (online now)

Arts and Crafts Wedge and Strap Bed #10: Stain, Lacquer, Hardware, and Lighting

09-23-2013 05:33 PM by pintodeluxe | 5 comments »

I stained and sprayed lacquer, and let the finish cure for 48 hours. Next I waxed the bed with Howard’s Walnut Wax and #0000 steel wool. Then I turned my attention to mounting the drawer pulls. I use Scott Collins “no math” method for laying out the hole locations. Then I offset the holes 3/16” higher than the layout mark, because the threads on the pulls are off-center. I use a full-size jig to mount the four pulls. -----Drawer pulls installed.-----I installed a...

Read this entry »


View Steve Erwin's profile

Entryway Arts & Crafts Mirror & Storage Bench #6: Progress Notes & Grand Finale

09-14-2013 06:15 PM by Steve Erwin | 1 comment »

Sorry for dropping this project blog. Life got busy and I wasn’t able to keep posting blog entries here on LumberJocks, but here are the highlights from the posts on my personal site. It’s done! :D I had a few delays I paused the project to figure out a finishing formula Quadrilinear Legs, Bookmatched Panels, Arcs, Frame & Panel Progress Made my own scratch stock Ran into trouble resawing for a bookmatched bench lid Another delay Scratch beading, floor ...

Read this entry »


View pintodeluxe's profile (online now)

Arts and Crafts Wedge and Strap Bed #9: Dovetail Drawers

09-11-2013 03:57 PM by pintodeluxe | 5 comments »

Time to build drawers for the bed.-----I am using a P.C. jig to machine the dovetails. Everything is pretty standard, except the bit I use, which is a larger 14 degree dovetail bit from Rockler. I like to set up two routers – one with a 1/4” straight bit, and one with the dovetail bit. -----I start by hogging out waste with the straight bit. -----The second pass is with the 14 degree dovetail bit. -----I find this two-pass method makes cleaner cuts, with less chance of the wo...

Read this entry »


View pintodeluxe's profile (online now)

Arts and Crafts Wedge and Strap Bed #8: The Wedge and Strap Inlay

09-09-2013 04:51 PM by pintodeluxe | 3 comments »

Here is the bed project, which is nearing completion.-----A couple of headboard details remain, one of which is the wedge and strap detail. I tapered the backsplash, and glued the wedges on. Next I use carpet tape to attach the backsplash to a strip of plywood. This serves as a reference edge as I cut the dado for the walnut inlay. -----I use a dado set and miter gauge to cut the shallow dado. I make sure to cut both ends of the backsplash before adjusting the fence. Normally one would ...

Read this entry »


View pintodeluxe's profile (online now)

Arts and Crafts Wedge and Strap Bed #7: Platform Support Boxes

09-08-2013 07:18 AM by pintodeluxe | 1 comment »

The platform support features ten plywood panels that transfer the load straight to the floor. One corner is knocked off, so it won’t be visible under the arched sides of the bed. -----My wife and I worked on assembly of the carcase. We started by gluing and screwing five panels to the side rail. The top of the panels are flush with the groove in the side rails.A lower strip of plywood is then set into notches in the panels. -----Then another strip fills the top notch in the panels...

Read this entry »


« prev 1 2 3 4 5 6 7 ... 14 next »
133 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com