LumberJocks

Woodworking blog entries tagged with 'sled'

  • Advertise with us
View mIps's profile

Table saw sled #2: almost done

09-16-2013 08:49 PM by mIps | 2 comments »

The new sled is almost done and I am much happier with it. As you can see it’s a basic sled. No Schmancy bits but it runs better in the table, has a DIY T-Track and a blade box so, it’s a upgrade. The back fence is 2 pieces of 1×6 laminated together with glue and screws. I cut a slot in this 5/8” wide and 1/4” deep then laminated a piece of cheap 14” ply over it and cut a 1/4” slot in that to make the t-track. It’s a bit crooked at one ...

Read this entry »


View mIps's profile

Cut off sled

09-05-2013 12:35 AM by mIps | 1 comment »

I had a cut-off sled, but I wasn’t happy with it. it didn’t slide well at all, I wanted a taller rear fence, and I wanted to try to make some t-track to go on it. so, today, I took apart my old one and started planning the new sled. I was able to remove the old runners without breaking them, which is good, and also without ripping apart the decent plywood that was the base, also good. I was able to determine that the left side of the sled was where the poor sliding problem was a...

Read this entry »


View mIps's profile

Miter sled the 2nd

09-05-2013 12:28 AM by mIps | 1 comment »

I had a miter sled, but I didn’t really like it. It was heavy and bulky and, to be honest, not really that well made. So, since I had a few pieces leftover from trimming down the reclaimed counter top for my eventual router table, I decided to make a new one! This time I went in knowing a bit more about what I wanted and how I wanted to make it. The base is construction-grade 1/2” ply. Not the best but it’s what I had. the miter guide / fence pieces are leftover trim from...

Read this entry »


View ScottShaeffer's profile

How-To Make Log Furniture #9: Cut Pefect Circles How-To

06-19-2013 02:27 PM by ScottShaeffer | 0 comments »

Kris Williams of Rocky Blue Woodworks shows us how to cut perfect circles on a band saw including how to make the sled need to do it!

Read this entry »


View kiefer's profile

MAKING OF A COFFEE TABLE (PART5)

01-28-2013 03:32 AM by kiefer | 9 comments »

Well it has been a anxious and emotional week for me and not much got done on the table but such is life.This week I played around of and on with some yellow glue and some 1/8” walnut veneer ,I rolled on glue on both surfaces (three different types seen in the pic ) and let the samples dry until clear and layed it on the plywood , put a hot iron on the veneer and heated the glue until it bonded and followed with a piece of wood to rub it flat .The result was a nice strong bond and tryin...

Read this entry »


View NedB's profile

Projects #7: New Cross-cut Sled W.I.P.

11-17-2012 01:07 AM by NedB | 4 comments »

Hi gang, long time no post… I’ve been in and out of the shop lately, this week I’ve been working on another batch of cutting boards. THe last time I made boards back at the end of August, I found that on some of my boards, my cross cut sled was building in an uneven cut (out of square) when I was trimming for the flip/glue stage of the boards. My old sled was built about 8 years ago, and I”m sure the fence can be adjusted. I didn’t glue it down, just screwe...

Read this entry »


View NedB's profile

Tool thoughts #36: Time for a new crosscut sled

09-09-2012 06:38 PM by NedB | 5 comments »

I was cross-cutting the blanks for my latest set of cutting boards when I noticed that my cuts weren’t square. Not a big deal in this case, as I’m only going to be planing them down to thickness anyway, but in the long run it means that a Lot of projects have been ‘just a tad’ off, probably for awhile now. that shows the ‘variation’ here’s my venerable sled, just something that i threw together awhile back: it is about as simple as yo...

Read this entry »


View DrewM's profile

Crosscut Sled for Table Saw

05-29-2012 07:21 PM by DrewM | 15 comments »

I made a quick video that provides an overview of the features of my crosscut sled. Thanks for watching.

Read this entry »


View Retsof's profile

Table Saw Jigs #1: A Crosscut / Miter Sled for Craftsman 10" Table Saw With Non-Standard Miter Slots

04-13-2012 03:03 AM by Retsof | 2 comments »

Here’s a link to a video that I made about my new crosscut / miter sled that I built for my Sears Craftsman 10” Table Saw with non-standard miter slots. I hope this helps some others who are looking for a solution to improve the accuracy of cross cuts and miter cuts with similar inadequately equipped table saws. I added the miter cutting features after this video was made, so I will have to update the video or include some new photos at another time. http://youtu.be/0Gr5t...

Read this entry »


View Joe Lyddon's profile

Crosscut Sled from ShopNotes #99

04-05-2012 03:43 AM by Joe Lyddon | 2 comments »

I started out making the Crosscut Sled as in ShopNotes Vol.17, #99… Page 24. I was doing OK, except that the one in the magazine was made for a Right Tilt Blade…... Mine is a Left Tilt; therefore, I dropped many of the features that I liked and it resulted in more of a straight vanilla Sled. It does have an extension that can be added for longer material… Here are the pictures taken…

Read this entry »


« prev 1 2 3 4 5 6 next »
59 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com