LumberJocks

Woodworking blog entries tagged with 'shoulder plane'

  • Advertise with us
View mafe's profile

Low angel shoulder plane DIY (Div style plane) #1: Making the body part one.

05-24-2011 11:23 AM by mafe | 48 comments »

Low angel shoulder planeBecause it’s fun…. Before you start reading I want to tell that I finally managed to make it run!It was giving me a headache, but once I found out the problem it was right on. Here is a video showing it in action. But I will blog a improved version also in this blog serie. Not so long ago I followed a class here on LJ with Stefang where we build a bucket, part of this project was to make a convex hand plane (Krenov style). So what have this...

Read this entry »


View Div's profile

Building a wooden shoulder plane #3: The mouth. Don't open wide, we are not at the dentist! (sorry Ken)

05-23-2011 10:47 PM by Div | 23 comments »

As I write, my blue Monday is behind me but some of my American friends are still busy dealing with theirs! Let’s get rid of the blues and go back to our project. The glue is dry and we can pop the clamps. I’ve always liked this stage of a project, that moment when you can take off the clamps and clean up the glue lines. Again, a reminder of what we want to achieve: This is where we are. Cut the pins close to the timber and clean up the glue lines. If there is glue squeeze ou...

Read this entry »


View mafe's profile

Low angel shoulder plane DIY (Div style plane) #3: Making the body part two.

05-26-2011 01:28 AM by mafe | 36 comments »

Low angel shoulder planeMaking the body part two. So here we go. In last blog we left the body to dry.Now time to make one of the sides flat by grinding of the pin ends. Then the band saw, for shaping that body.In the back left my future dinner knifes, its Swedish steel and eight different woods for the handles, in this way people can choose, and find a favorite (sorry it has nothing at all to do in this blog). Cutting after the circle that I decided for the design. Shaping and...

Read this entry »


View mafe's profile

Low angel shoulder plane DIY (Div style plane) #4: Drawings Analys and Documentation...

05-26-2011 07:05 PM by mafe | 10 comments »

Low angel shoulder planeDrawings Analysis and Documentation… I promised to post a set of drawings for this project, normally I will not do this, but due to the fact I was spending the time drawing it to figure it out I decided to make a few drawings to help others build.(And no one just do that, it took 6-8 hours of work, and 8 hours of building and thinking, so just thinking of the fact that I should receive 75 dollar from a woodworking magazine and be happy makes me laugh it would ...

Read this entry »


View mafe's profile

Low angel shoulder plane DIY (Div style plane) #2: Making a blade from another plane iron.

05-24-2011 12:57 PM by mafe | 16 comments »

Low angel shoulder planeMaking a blade from another plane iron. This is the second part of the blog, in last part the plane body was made. This is where we will end, Div’s shoulder plane on top, then mine and finally what this part is about; the plane iron. Since I have a handful of block plane irons I got for next to nothing, I will ‘kill’ one of these.Measure the width of your shoulder plane and add a little for later tuning (I added 1mm).Draw this on your plane ...

Read this entry »


View Div's profile

Building a wooden shoulder plane #4: Let's make us an iron!

05-25-2011 10:12 PM by Div | 16 comments »

If this is happening a little too slow for your liking, it is because I have to make sawdust all day long to keep the wolf from the door. That is 10 hours gone. Making these little planes and blogging about it is mostly a night time affair, after taking care of normal daily chores and duties! We have made a plane body and it is looking pretty good! Time to do some metalwork.This is what we want to achieve: At the top is the finished plane iron, below is the material I made it from; ...

Read this entry »


View Andy Panko's profile

Building My Roubo Bench #6: Starting the Legs

02-12-2012 04:13 AM by Andy Panko | 2 comments »

Now that the top is done, it’s time to start the legs and stretchers. I wanted real thick and sturdy legs, so I’m going for 5” square. Prior to starting this project, I had never done any real lamination work. I’ve glued boards together before, end-to-end, to make wider planks. But that material was only 1/2” thick. I never did anything this big before, but this whole lamination thing seemed pretty easy in concept. Sure enough, it wasn’t too bad. Now...

Read this entry »


View mafe's profile

Low angel shoulder plane DIY (Div style plane) #5: The basic cuts.

05-27-2011 11:38 PM by mafe | 8 comments »

The basic cutsThis should have been first… I know this was how the blog should have started but I had not planned to take photos when I started so this is why – but since I decided to make some more planes I took pictures after. So here it is ‘The basic cuts’. As so often recycle is the basis – here a piece of Ash wood that comes from the cut out for a kitchen sink.Its big wonderful staves that I simply cut out again by cutting in the glue line, ...

Read this entry »


View Div's profile

Building a wooden shoulder plane #1: First you gotta do some thinking...and find iron

05-20-2011 10:05 PM by Div | 23 comments »

During the recent posting by Bertha on the hand planes of our dreams, the issue of wooden shoulder planes came up. I had some requests and PM’s to blog on the making of a wooden shoulder plane so I will give it my best shot. Be warned, I work in the metric system so measurements are in millimeters. For those who use King George’s thumb to measure, dividing by 25.4 will at least give decimal inches. I’ll gladly answer any question but have patience: No computer will survive in my dusty worksho...

Read this entry »


View Karson's profile

Shoulder Plane - Mason Dixon Style

01-11-2009 10:50 PM by Karson | 11 comments »

The Woodcraft Magazine Aug/Sept 2008 had a plan for a Shoulder Plane. Our woodworking club decided to make that item as a workshop. The workshop was held Jan 10-11, 2009. We had 12 people take the class, the cost was $13.00 for the blade purchased from Woodcraft and $10.00 if you wanted the wood supplied by the instructor. The wood that he supplied was Tiger Maple with Madagascar Ebony sole. Some Sapele was provided as glue strips for the planes. My son David and I took our own ...

Read this entry »


1 2 next »
20 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com