LumberJocks

Woodworking blog entries tagged with 'sharpening'

  • Advertise with us
View WayneC's profile

Handplane Restoration #29: Stanley #62 Part 2 - Inspection

06-11-2011 12:48 AM by WayneC | 25 comments »

Whoot. The plane arrived today. I unpacked it and started the inspection. I only found one surprise which is a good thing. Now all I need is for the IBC blade to arrive and I will be ready to “get er done”. I picked up some brass sheet and rod yesterday, so I can also begin the process of creating a new lever to adjust the mouth. Thanks again Mads!!!! So here are some photos. Side view Things to look out for in this photo. If you look at the depth adjustment...

Read this entry »


View BigRedKnothead's profile

Sharpening 101 for Newbies- What Should I Use? #1: Sharpening Methods I've Tried

03-04-2013 01:53 PM by BigRedKnothead | 22 comments »

Early on, a woodworker is forced to decide upon a sharpening system or product. And I know we have some folks on Ljs who are just entering the wonderful world of hand tools. This is my attempt to not leave those people hangin when it comes to sharpening. Clearly, planes and chisels are just handsome paperweights if they’re not sharp.Let me start by saying that I am far from an expert. Shoot I’ve only been using and sharpening hand tools effectively for about a year. I spent the pr...

Read this entry »


View DouginVa's profile

My "new" $50 Craigslist Jointer

01-22-2013 02:36 AM by DouginVa | 22 comments »

So for the past 20 or so years I’ve had the below Rockwell 4” jointer. I bought it for $50 off the carpenter that added the second floor to my home. It needed a little work, but for the most part it served me well over the years. The downside, obviously, was the short bed and only a 4” width. So I’ve been searching for a long time for a Craigslist special. Then I saw a post for a 6” Delta jointer for only $100. I then noticed the author’s commen...

Read this entry »


View SPalm's profile

Shop Stuff #2: Fingernail Gouge Sharpening on the WorkSharp

05-22-2013 03:08 PM by SPalm | 22 comments »

While learning to turn, the tools in use eventually need to be sharpened. I looked at various jigs, holders, and solutions for sharpening. I own a WorkSharp, but I thought that I would not be able to do it all on this machine. But I have made a series of jigs, and am now able to sharpen all my major tools with it. First up is the trickiest one. The hardest one to do is the Fingernail, or spindle gouge. Tormek and others have bars that slide out and pockets that hold the handle. I just...

Read this entry »


View StumpyNubs's profile

The Stumpy Nubs Workshop #40: Stone, paper, daimonds... Sharpening made simple!

08-05-2013 07:39 PM by StumpyNubs | 22 comments »

Part one of a two episode sharpening series takes a look at the manual sharpening methods including “scary sharp” using sand paper, oil and water stones, and diamond plates. Stumpy gives some money saving ideas for surface plates and diamond sharpening, reviews the Rockler plate glass sharpening system, and gives a behind the scenes look at what’s been going on in the workshop…. that and more on the latest episode of Blue Collar Woodworking! After you watch this one...

Read this entry »


View Brit's profile

English Mortise Chisels #1: Design Details

09-15-2013 05:02 PM by Brit | 22 comments »

I picked up this I. Sorby English mortise chisel with the Punch logo the other week and finally got it cleaned up and put back into service. The chisel is 33cm (13”) long and 7mm (a touch over 1/4”) wide at the back. The handle is an oval shape and tapered in both directions. The end of the handle is slightly domed to help prevent a glancing mallet blow from chipping the side of the handle. A hard leather washer separates the handle from the bolster. The cross-section of...

Read this entry »


View Dick, & Barb Cain's profile

"REVERIE HARP!" a new style of Harp from a kit #3: Making some carving tools.

08-04-2009 11:12 PM by Dick, & Barb Cain | 21 comments »

I haven’t got much done yet on the Celtic Knot carving. We’ve been up at our cabin, & there’s a lot of upkeep that hasn’t been done in the last couple of years, so please be patient with me.~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ This is how far I’ve gotten so far.~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ I started getting sore fingers from this knife I’ve been using. So I decided to make something...

Read this entry »


View OregonBurls's profile

The Burl Hunter (I need 5 people to help me)

05-04-2010 03:56 PM by OregonBurls | 21 comments »

Hey everyone,I am in need of some help! I am writing a book called “The Burl Hunter”. I am looking for interested people who are willing to read as I write to help me out. I am not a great writer but I love to teach. What I would like to do is get about 5 people to read and critique the book. Even edit my grammar. I would like 2 people who know about burls just to keep me in check and 3 to just read to learn and see how it flows. I need your input. It is a book that will g...

Read this entry »


View SPalm's profile

Shop Stuff #3: Sharpening Gouges and Skews on the WorkSharp

05-24-2013 05:55 PM by SPalm | 20 comments »

This is part two on my journey of sharpening my lathe tools. The first part was a Fingernail Gouge. Now on to the standard Spindle Roughing Gouge (SRG) and a Bowl Gouge. Both of these gouges are sharpened at 45 degrees. I started out making a triangle ramp to lift the gouges at 45 degrees, with grooves to roll the gouge in, but I gave up on it for now. One problem that I had was that my roughing gouge is not a perfect circle – it is more like a smiley face. It would not roll well in the ...

Read this entry »


View RonPeters's profile

Making a Violin #5: Carving the plates

01-16-2011 08:21 AM by RonPeters | 20 comments »

Ok, I’ve been busy with life and could only get to the violin as weather permitted, that is until I insulated the garage and installed an IR heat lamp which takes the chill off the air. This is the maple back. I’ve carved guides using templates I made out of aluminum. After aligning the guides to the plate surface it’s a simple matter of carving away the excess and blending. There are 6 templates. 1 through 5 are horizontal left to right with the last spanning the length....

Read this entry »


« prev 1 2 3 4 5 6 7 ... 42 next »
416 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com