LumberJocks

Woodworking blog entries tagged with 'screw'

  • Advertise with us
View Tom's profile

Moravian Workbench #4: Turning the vise screw

09-12-2019 11:52 AM by Tom | 2 comments »

Now that the vise is operational, I wanted to turn a more pleasing shape on the vise hub. The challenge is locating the turning centers for the lathe. On the screw end, there were marks that appeared to be centered, so I could use that for the drive center. However, on the hub side, it was just a smooth flat surface. I used a simple method to locate a good center. I set the hub end on a piece of plywood and nailed four brackets around the hub to restrain it from moving laterally. ...

Read this entry »


View Bill Berklich's profile

Of Tool Cabinets, Chewing Gum and Sealng Wax #12: Split nut screwdriver

03-16-2019 06:43 PM by Bill Berklich | 3 comments »

Lots of projects as every other LJ’er but this Split nut screwdriver is (in my mind) a good looking success. Like every project I do there is always something else I need before I get started on the main event. The Split nut Screwdrivers started because 1) so many LJ’ers have made so many really cool saws and 2) I have a couple of old back saw plates and 3) I REALLY needed a project for the LJ Spring Swap… :-) Casting about LJ and the net I came up wiith sever...

Read this entry »


View IantheTinker's profile

Where to Buy Screws

01-27-2018 04:44 AM by IantheTinker | 7 comments »

I mostly purchase general construction screws from Menards, the Star-bit drive ones because they don’t cam out on me like the Phillips heads do. I get them there for $3.79 per one pound box, a great price for a good screw. However, they don’t carry any shorter than 1 3/4”, so I tried at Home Depot. I found some star drive screws there for $5.78 per one pound box and they had 1”, 1 1/4”, and 1 5/8” sizes, so I was quite pleased. The price was also pretty decent in my estimation. Over at Lowe’s...

Read this entry »


View WayneC's profile

Handplane Reference #8: Bench Plane Screw Sizes.

10-03-2013 06:05 PM by WayneC | 14 comments »

Collecting this information from a variety of web resources. Please watch the type of thread as well. Record Here are the sizes from Recordcollector’s site: Cap Iron screw : 5/16” 18tpi BSW (I believe this is the only standard BSW thread on bench planes)Frog screws : 7/32” 20tpi Whitworth;Tote & Knob bolts : 7/32” 20tpi Whitworth;Tote Toe screw : 7/32” 20tpi Whitworth;Frog Adjusting Plate screw : 7/32” 24tpi Whitworth;Frog Adjusting screw : 1/...

Read this entry »


View chopnhack's profile

Mobile Workstation #2: Let's do the twist!

03-16-2012 11:44 PM by chopnhack | 1 comment »

Ok, so it’s much more fun to dance than to fix…. Apparently welding a frame should not be undertaken without proper support, or ahh… more experience. The frame had a twist to it across the 59.5” length! I cleared a section of the shop floor (miracle) got out my door installation level and found a fairly level area. I then proceeded to use some shims to adjust the floor until the it was perfectly level. Gotta give credit to the guys that screeded the floor some 50 y...

Read this entry »


View CartersWhittling's profile

Workbench #10: Making Wooden Nuts

10-08-2011 04:35 AM by CartersWhittling | 27 comments »

Hello. In this video I show you how I make wooden nuts for my bench with a tap my friend Chris Legendre and I built. I explain some of the details about the tap and show you how its used and set up. Again like I mentioned in my last blog entry, I will be making a video later showing you how to acually make the tap. https://www.youtube.com/watch?v=cztX3GSPBYM&list=UU6RUw1NtwJL0P9C86W54keg

Read this entry »


View PurpLev's profile

Machinist Toolcart #11: Almost there. The end of all marking and cutting

09-12-2011 05:48 AM by PurpLev | 20 comments »

We had a beautiful weekend, blue clear sky, sun shining and smiling, birds were singing, even the temperature was behaving – just a beautiful weekend. and I was sick. I waited until I could regain enough focus since loss of focus in woodworking is a bad idea and can only lead to disastrous consequences either to the project or worse to ones self and trotted to the garage only to find that the material I had planned to use didn’t look all that fitting to the purpose of acting...

Read this entry »


View PurpLev's profile

Beads Box #10: Get Up on your Feet! Routing Safety and Avoiding Tearout

01-10-2011 01:35 AM by PurpLev | 11 comments »

I was able to get to the garage today as a request for a new shelf for the kitchen was in. While there I saw some cutoff pieces of mahogany that I had piled up from the past 2 projects, and saw 4 legs hidden in those waiting to come out to life. I had wanted to put legs on this box from the get go but wasn’t set on a design that I liked and was mentally blocked with it. I decided to make 3 1.5” x 1.5” x 1” legs and just chamfer the bottoms – just to have so...

Read this entry »


View Eric's profile

Screw Rehab: The New Head

06-05-2010 03:48 PM by Eric | 1 comment »

A complete stranger might think I’m bitter about being treated for drug dependency or something…no, no, not that kind of rehab… Today I glued up the block that will eventually be the new head of my old screw. Just for fun, I decided to laminate a piece of pine in the middle of two pieces of kapur. I don’t know what this might do as far as wood movement, as far as laminating softwood in between hardwood – I have no idea but I don’t care! It’s fu...

Read this entry »


View PurpLev's profile

Router Table #13: Leveling the Insert - Incra Style

02-01-2010 06:18 AM by PurpLev | 10 comments »

Up until now I was leveling my insert (also on my TS) with blue painters tape – yeah, ghetto, but it works, cheap, and available. When I made the order with Lee Valley last week, I ordered a pack of 10 capscrews and though I’d try to incorporate the leveling concept on the Incra made table. as I stated in my previous post- If I had to start it over, I’d just order the table top from Incra and be done with it – they are worth their price. however. since I already had...

Read this entry »


1 2 next »
18 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com