LumberJocks

Woodworking blog entries tagged with 'scratch build'

  • Advertise with us
View htl's profile

Shop jigs #3: Wheel making jig Setting it up

10-29-2018 11:47 PM by htl | 5 comments »

A helper post for the tread making jig. Here is the jig in straight mod but I need angle tire treads so! Take out the two screws holding the base down, then pull up and turn the frame for angled mod, using the dowels to line everything up, them screw it down so everything stays in place. I cut off the corner so the fence could get in closer. I added a stop block at the back of the table saw so i wouldn’t have to think about stopping ,just hit the stop and on we go. Th...

Read this entry »


View htl's profile

Toy Construction #267: Scratch build Steam Train

08-23-2019 11:07 PM by htl | 10 comments »

This will be a scratch built Steam train in the style of the 1860’s or there about.Something like this. Here’s where I got to today.I have three partial days in it, one of those spit and sputter builds. I have the plans for both Toys and Joys trains but wanted it to have a longer look to the boiler.I have built both the wood and coal T&J’s Trains.Started with the frame.The back is 3/4” and went back and thinned the front part down to 1/2”, I used dowels...

Read this entry »


View htl's profile

Toy Construction #183: Front and back suspension that works

02-12-2018 11:57 PM by htl | 18 comments »

Front and back suspension that works on the Mack dump truck.Rain rain go away so I’ll stop hurting but didn’t let the work stop. Up and Down Now for the front Up and down with the front end.

Read this entry »


View htl's profile

Toy Construction #186: Just about there with the Mack.

02-22-2018 01:01 AM by htl | 11 comments »

If I add front wheel drive does that make this a 6 wheeler or a ten? The drive shaft follows the Differential on both the front and back. As I said just about there. Here's the finished project.

Read this entry »


View htl's profile

32 Ford working on the spoke wheels

07-26-2019 11:08 PM by htl | 11 comments »

Before I glue up the wheel wells I figured it would be a good idea to have the wheels so every thing lines up just right, so it’s wheel making time again. Here is where I got all my info for making spoke wheels, I do it a little different but this will give you all the info needed, I watched it 10 or more times before it all started to come together. There’s a hundred ways to do any thing but here’s what’s working for me right now for building spoke wheels. Dr...

Read this entry »


View htl's profile

Toy Construction #185: All the main parts are now mounted.

02-15-2018 11:45 PM by htl | 7 comments »

Cut and sanded out the dowel holes in the wrong place.Before After Also made a cab guard, I have no idea what it’s really called. Some shots with a different set a tires. Last I tried out a front bumper.

Read this entry »


View htl's profile

Toy Construction #228: Toyota 4Runner #2

09-19-2018 08:50 PM by htl | 6 comments »

Been wanting to try this build for a long time but now I’m beginning to question my sanity, I needed an easy build not this thing. LOL The top and windows aren’t glued in just a look see as my passions was at an end and needed to call it a day.Going to take some fine adjustment but should work out ok? And here’s a picture of my truck. LOL

Read this entry »


View htl's profile

Toy Construction #268: Scratch build Steam Train wheels

08-27-2019 07:23 PM by htl | 8 comments »

Got a little more done. Found out my tread making jig also does a pretty good job at making spoke wheels, sure saves a lot a time I would have to be drawing all the points needed to drill. Just add a blank and drill, once the jig is centered to the bit. The indexer is set up for cutting 36 treads but as you can see I have it marked for every other hole or as I did this time every third hole. As you can see the backer plate gets pretty chewed up when making the different sizes...

Read this entry »


View crowie's profile

Hot Rod FORDS #11: Nearly Finished

02-17-2018 07:56 AM by crowie | 10 comments »

Nearly Finished!! The body and back are glued to the chassis. The radiator is glued in plus added stays. No windscreen/windshield as I’m sure it wouldn’t last the little boys play tests. The rear bumper bar is done, BUT I’m keep that surprize for until the final revival. So all the needs doing is the seats glued in place, the wheels glued into the chassis plus a little detailing before 3-4 coats of satin polyurethane clear…..

Read this entry »


View crowie's profile

Hot Rod FORDS #6: What do we call the back of the T-Bucket?

02-06-2018 09:41 PM by crowie | 8 comments »

What do we call the back of the T-Bucket? Is it a pickup, a ute, a boot, a trunk?

Read this entry »


1 2 3 next »
27 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com