LumberJocks

Woodworking blog entries tagged with 'saw horses'

  • Advertise with us
View DocTux's profile

It Starts With a Workbench #5: Get this thing off the ground... with a vengeance

07-04-2015 10:20 PM by DocTux | 1 comment »

Started off working on my saw horses. I definitely appreciated the advice to build a saw bench, but it was going to be significantly more involved than the extremely basic set of stacking saw horses I did build. Plus it can’t stack, which was a huge detractor. I will likely build one later on, but probably not until I have a functional bench in place. This was the first time I had ever used a handsaw and attempted to do more than a rough cut to fit oversized studs in the back of my truck. It ...

Read this entry »


View DustyMark's profile

Building a KARA Hummer Layout Duck Boat #1: Building the Lower Frame

05-11-2015 07:00 PM by DustyMark | 6 comments »

The Requirement I moved back to MN in June 2014, after nearly 30 years away, and my brother quickly introduced me to duck hunting. We’re not on any of the major flyways here, so we need to put everything in our favor possible. We read about the advantages of layout boats in providing maximum concealment from wary ducks and talked about it in the duck blind all last season. Our hunting party consists of my brother, my nephew, and me and we decided to build three one-man layout boat...

Read this entry »


View ruddhess's profile

Southern Yellow Pine Work Surface (workbench) #14: Transition from Dovetails to Rabbet Joints

03-13-2015 01:44 AM by ruddhess | 2 comments »

If thy dovetail offend thee, cut it off! I decided to not use these dovetails that I have been practicing on. I read on two different articles that you should practice on scrap wood and not on your project (which is what I have been doing). Plus, I want the joints to reflect a similar quality/skill level as the rest of the project. So, I am “ditching” these dovetail pieces and transitioning to rabbet joints (not as strong, not as “flashy”, but adequate) with oak dow...

Read this entry »


View ruddhess's profile

Southern Yellow Pine Work Surface (workbench) #13: Dovetail Saga - Dovetail Number Four

03-13-2015 01:25 AM by ruddhess | 0 comments »

Pic of the tails (I’ve miss designated some of the other pictures in DT 2 & 3 I think – calling them tails when they were actually pins – doh!) on the second top piece. More tails – this piece really has a lot of resin in the knots – smells good, but gums up my saw a lot. The resin makes the wood almost translucent. Had to trim a shave off the pins to make it fit right. That’s a sliver for sure – all done with an old Stanley back saw &...

Read this entry »


View ruddhess's profile

Southern Yellow Pine Work Surface (workbench) #12: Dovetail Saga - Dovetail Number Three

03-13-2015 01:10 AM by ruddhess | 2 comments »

Tails of dovetail number three. Middle is humped up, but at least it’s not cut past the mark like the ends are. Starting to look sloppy. I’m not sure if I was getting tired or what here. Good picture though – the camera decided to focus on the boxes and stuff in the background. Dovetail number three I think – Whoa! Little bit of a gap there dude! And the view from the end – Wow, too much space in between the parts. I know what happened though. The first ...

Read this entry »


View mafe's profile

Japanese tools #10: Japanese saw horses - floor horses (blog)

05-24-2012 07:47 PM by mafe | 17 comments »

Japanese saw horsesfloor horses This time low saw horses, these are for Japanese woodworking, and so they are meant to keep the items in good position for sitting work and for bend, standing jobs like rip cut with a Japanese saw. Once more a roof rafter that a friend gave me nice thick wood and wide also, the same as I used for my shaving horse (thank you Jakob).First step is to mark up careful with pen and Sashigane (Japanese square).And do not forget a cold beer…. Now sin...

Read this entry »


View Ecocandle's profile

Extremely Average #13: Dumb Mistake

01-15-2010 05:11 AM by Ecocandle | 17 comments »

It just makes me so darn angry. The life I have led has been one of logic. I am the son of a mathematician and much of my adult working years have been spent as an analyst. When I make a dumb mistake it grates on my nerves worse than finger nails on a chalk board. Now I don’t have delusions that I am going to progress in woodworking mistake free. Quite the contrary, I see my mistakes as an opportunity to learn. I have learned a lot. The angst I am feeling come from not only makin...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com