LumberJocks

Woodworking blog entries tagged with 'qswo'

  • Advertise with us
View pintodeluxe's profile

Stickley / Jeff Jewitt Arts and Crafts Finish

04-15-2013 01:24 AM by pintodeluxe | 14 comments »

I wanted to recreate this Jeff Jewitt finish from Fine Woodworking #157, however the article didn’t list which formula was used. I consulted with Jeff, and it was Transtint Brown Mohogany dye, followed by McCloskeys Walnut stain. McClosky no longer makes stain, but sold to Valspar / Cabot. ---So I set out to make a sample board to achieve the rich, dark color I was after. ---The top colors are stain only, the middle colors are dye first then stain, and the bottom color is dye only. ...

Read this entry »


View pintodeluxe's profile

Arts and Crafts Entertainment Center / Sideboard #6: Lacquer, Wax, and Hardware

04-01-2013 04:51 PM by pintodeluxe | 1 comment »

After mounting the slides, I used carpet tape to temporarily attach the drawer fronts. Slides are Centerline 757’s, and mounting is the same as my dresser project here… http://lumberjocks.com/pintodeluxe/blog/34281 -----Drawer fronts installed with 4 screws each.-----Since the drawers are graduated from 6” to 9”, I made a full sized pattern for the largest drawer. Then I marked the size of the other drawers, and used those lines to lay out all drawer pull holes o...

Read this entry »


View pintodeluxe's profile

Arts and Crafts Entertainment Center / Sideboard #5: Wedge and Strap Backsplash, Trimming Top, and Staining

03-25-2013 02:18 AM by pintodeluxe | 10 comments »

So this is where we left off with things last time…-----The entertainment center features a wedge and strap backsplash to match my 6 drawer dressers http://lumberjocks.com/projects/79208 -----Basically it is a shallow dado that receives a walnut inlay. I cut tapers on the backsplash first, then glued the wedges back on. I carpet-taped a strip of plywood to the backsplash to give me a straight reference edge to cut the dados (note to self: rip plywood strip before installing dado bla...

Read this entry »


View pintodeluxe's profile

Arts and Crafts Entertainment Center / Sideboard #1: Side Panels

02-26-2013 08:38 PM by pintodeluxe | 9 comments »

Here is the next project, an entertainment center that is reminiscent of a Stickley sideboard. The central slat detail gives a nod to Kevin Rodel. The backsplash features my “wedge and strap” detail, also found on my A&C dressers. ----- Leg blanks are laminated from 3/4” stock. Next I add 1/4” thick veneers on two sides. Even though the finished veneers will only be 3/32” thick, I leave them 1/4” thick for now. I find that 1/4” stri...

Read this entry »


View pintodeluxe's profile

Arts and Crafts 6 Drawer Dresser #9: Dovetail Drawers , Spraying Shellac

01-22-2013 06:03 AM by pintodeluxe | 2 comments »

Here is my setup for cutting half blind dovetails. I use a larger-than-stock 14 degree dovetail bit. I think it makes nicer looking dovetail joints, and they feel much stronger. Here is a link to my blog about the special bit… http://lumberjocks.com/topics/40073-----This is the bit I use, which is a Rockler item. You can still cut these dovetails in one pass with the PC jig. -----I trimmed some aromatic cedar plywood to size and test fit the drawers.-----Grooves were cut for the dra...

Read this entry »


View pintodeluxe's profile

Arts and Crafts 6 Drawer Dresser #6: Web Frames

01-02-2013 08:53 PM by pintodeluxe | 1 comment »

It is now time to build the web frames that function as drawer dividers. The web frames are notched around the legs, and I decided to cut the notches with a dado blade. Here is my setup at the tablesaw with sacrificial fences on both the tablesaw and miter gauge. The result was nice crisp corners on the notches. This will be a visible joint at the front of the dresser. A bandsaw could also accomplish the task, but not quite as easily as a dado blade. After cutting pieces to ...

Read this entry »


View pintodeluxe's profile

Twin Tenon Arts and Crafts Dining Table #6: Finishing Touches

09-11-2012 04:49 PM by pintodeluxe | 9 comments »

Top finished Frame assembled Four-inch long T30 lags secure the top timbers. Laminated or not? By laying out my jointlines carefully, I was able to laminate some 8/4 and 5/4 together. The glueline is at the angle of the timber, so it is not visible. In addition, I laminated some thin veneers on both sides. Back to the project page… http://lumberjocks.com/projects/71281

Read this entry »


View pintodeluxe's profile

Twin Tenon Arts and Crafts Dining Table #4: End Assembly Glueup and Decorative Pegs

09-04-2012 05:59 PM by pintodeluxe | 1 comment »

End assembly joints are drawbored and pegged with 3/8” walnut pegs. I use this pounding block to set the walnut buttons to the right depth. The buttons conceal slotted screw holes that attach the breadboard ends. Next up is fitting the keyed tenons that connect the two end assemblies.

Read this entry »


View pintodeluxe's profile

Twin Tenon Arts and Crafts Dining Table #2: Long Arched Rails, and Tabletop

08-24-2012 02:20 AM by pintodeluxe | 4 comments »

After pattern routing the long arched rails, it was time to turn my attention to the top. I started with 6/4 stock, all from the same log. Biscuits were placed every 6” to help with alignment and add strength. I once did an experiment with biscuits – joined two boards with biscuits (no glue) and soaked them in water for a while. I took it around to each family member to see if they could pull the boards apart—- and none could. I took the top over to Creative Woodwo...

Read this entry »


View pintodeluxe's profile

Twin Tenon Arts and Crafts Dining Table #1: Frame components and tabletop

08-22-2012 06:09 PM by pintodeluxe | 2 comments »

I wanted to design an arts and crafts dining table that included arched rails and twin keyed tenons. I like several of the Stickley tables, but wanted something original. I like the feel of Keven Rodel’s Talesien desk, which served as inspiration for this table. The stack of parts is growing… Initial frame assembly… And the tabletop glueup…

Read this entry »


« prev 1 2 3 4 next »
38 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com