LumberJocks

Woodworking blog entries tagged with 'qswo'

  • Advertise with us
View pintodeluxe's profile

Arts and Crafts Entertainment Center / Sideboard #1: Side Panels

02-26-2013 08:38 PM by pintodeluxe | 9 comments »

Here is the next project, an entertainment center that is reminiscent of a Stickley sideboard. The central slat detail gives a nod to Kevin Rodel. The backsplash features my “wedge and strap” detail, also found on my A&C dressers. ----- Leg blanks are laminated from 3/4” stock. Next I add 1/4” thick veneers on two sides. Even though the finished veneers will only be 3/32” thick, I leave them 1/4” thick for now. I find that 1/4” stri...

Read this entry »


View kordwood's profile

finally getting close to the finishing room ...

04-01-2009 05:33 AM by kordwood | 9 comments »

I’ve been working on a big Stickley designed double bookcase for way too long, but I’m closing in on it now. Finally put the tongue-and-groove back boards on, all the shelves are done (middle shelves are fixed, top and bottom shelves adjustable … it was too tall for me to get a full top to bottom shot, so you can’t see all the shelves in this pic), it’s all glued up and ready for some final sanding. It’s coming out fairly well, if I do say so myself.But it&...

Read this entry »


View pintodeluxe's profile

Stickley #369 Morris Chair #7: Ottoman

03-25-2014 04:24 PM by pintodeluxe | 8 comments »

Here I am building a small ottoman to compliment the Morris Chair. -----The ottoman legs were laminated with thin veneers. As with the chair, I used 1/4” thick veneer strips that are later planed down to 3/32” thickness. -----The ottoman legs are planed to their final size of 1-3/4” square, and mortised to receive 1/2” thick tenons. -----I do an initial assembly to see how the joints fit. Everything is scaled down on the ottoman, compared to the Morris chair. Th...

Read this entry »


View pintodeluxe's profile

Arts and Crafts Library Desk #5: Bullet Board, Jeff Jewitt Style Finish

12-18-2013 08:06 PM by pintodeluxe | 8 comments »

In part 4 of this series I pre-raised the grain, and applied the initial coloring with Transtint Brown Mohogany Dye. When the dye is wet it looks amazing, but quickly dries to a lifeless sheen. -----The drawer fronts were stained before assembly. After the glueup dried overnight, the drawers were lacquered. -----The desk was stained with Varathane Dark Walnut oil based stain. When wet the stain looked great, but it too dried to a grayish cast. Not to worry though, once the lacquer was a...

Read this entry »


View pintodeluxe's profile

Stickley #369 Morris Chair #8: Stain and Lacquer

04-04-2014 08:30 PM by pintodeluxe | 8 comments »

I sprayed the chair with Rodda #19 stain, which I thin with a splash of mineral spirits.-----After the chair had dried for 24-48 hours I sprayed Rudd lacquer (Satin sheen), which I strain and thin 20% with lacquer thinner. After the first coat I sanded with 320 grit soft sponges, and cleaned the dust with cheese cloth (not tack cloth) and compressed air. -----After the second coat I wet sanded with 1500 grit soft sponges. The whole chair only took 15-20 minutes to wet sand. -----The Rudd ...

Read this entry »


View pintodeluxe's profile

Arts and Crafts Library Desk #3: Inside Corbels

12-10-2013 06:54 PM by pintodeluxe | 8 comments »

This is where we left things last time…-----The desk is quite strong, however it looks pretty plain at this stage. The next step is to add 8 inside corbels, so I made a template routing jig. I like to use toggle clamps, because they double as handles when routing. Carpet tape also works, but for workpieces this small I prefer toggle clamps to keep my hands clear of the bit. -----After cutting the rough shape at the bandsaw, I trim the corbels to size at the router table. Notice how...

Read this entry »


View pintodeluxe's profile

Arts and Crafts Library Desk #4: Secret Compartment Drawers , Transtint Dye

12-16-2013 05:16 PM by pintodeluxe | 7 comments »

With the corbels installed, we can move on to the drawers. -----Here my son sands the drawer parts. -----I made the drawer parts 3-1/4” (the exact width of the drawer opening) to accommodate my dovetail jig. After the dovetails were milled I edge planed them to final size, being careful to remove an equal amount from both edges. -----The dado creates two sections to each drawer.-----The 3/4 extension undermount slides will only display the front drawer compartment. Releasing the fr...

Read this entry »


View pintodeluxe's profile

Mission Dining Build #5 - Table Apron, and final assembly

12-07-2011 10:51 PM by pintodeluxe | 7 comments »

The table assembly is now complete. Since the leaves store in the table, the aprons needed to be hinged. I used short piano (continuous) hinges from hardware source.com. The hinges are 4.5” long, and lock at 90 degrees, similar to jewlery box hinges. I used inset rare earth magnets to lock the hinged aprons in there in-use positions. Felt lines the frame, which creates a nice little nest for the leaves. The table extends to accept two 12” leaves v...

Read this entry »


View pintodeluxe's profile

Stickley #369 Morris Chair #1: Leg Laminations and Angled Tenons

02-24-2014 09:27 PM by pintodeluxe | 6 comments »

Here is the project at hand, a slant arm Morris Chair. I am working off plans from the Popular Woodworking April 2011 issue, which I recommend you buy. The Author is Robert Lang. He posted a free diagram to Sketchup, but with this detailed of a project, you will want to order the back issue. My techniques differ from Robert’s methods significantly, so I will try to elaborate along the way. -----I like to start by laminating the legs for quartersawn figure on all four sides. ...

Read this entry »


View kordwood's profile

Ellis-Mackintosh-Limbert mashup table #3: Glaze applied

11-23-2018 09:22 PM by kordwood | 4 comments »

Rubbing the walnut gel stain really fills the pores of the oak. I’ve found it’s important to wipe it off thoroughly —and quickly — in order to get good contrast. This piece is small, so I didn’t have to use mineral spirits to remove excess glaze. In 24 hours or so, it’ll be ready for the first of two coats of satin Waterlox.

Read this entry »


« prev 1 2 3 4 next »
38 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com