09-10-2009 03:22 AM
by Porosky |
54 comments »
Hey everybody, after a few personal messages here is my version of a how to on a Drunken Checker Board. I of coarse bow to the Chairman of the Board and pay tribute with beer. This is a Off-Checker pattern I call “Drunken Alice in Wonderland” The “serendipitous” nature of this piece is appealing in a far out sort of way. Here Goes…
So first I prepare the Material. I am using Hard Maple and Walnut both are surfaced flat and cut 1” x 9” x 14&...
Read this entry »
08-06-2008 12:26 PM
by ganders |
26 comments »
The quick and dirty instructions on how to make a zig-zag pattern cutting board.
Click on the pictures to see a full size image.
Choose a couple different types of hardwood. The more colors the better. Below is cherry, maple and walnut. Rip strips of wood any width so the total with is about 12”. This is the width that will fit through my planer. The beauty of this is that none of the widths have to be the same. The board shown below is made of scrape wood. If you only have shor...
Read this entry »
04-11-2010 02:36 AM
by patron |
25 comments »
i saw sinister’s cutting board last night ,http://lumberjocks.com/projects/30543and saw so many wondering how it was done ,i happened to have a bunch of exotic strips for something else ,and decided to do a board like his .to save him the trouble of drawing a tutorial for everyone about the build ,i took pictures of all the steps .i have sent him a PM asking his permission to post this ,while i await his response , i will be downloading into photobucket . .later ,no word from sinister y...
Read this entry »
02-20-2013 05:22 PM
by WoodJediNTraining |
17 comments »
This Week I show you how to make a folding out feed table for your table saw. This design was based after an article and plan found in a 2009 issue of Woodworker’s Journal Magazine. Originally the plan was designed for a Cabinet saw with a Biesemeyer Fence System, so I had to make some slight modifications for my Porter Cable Saw. In this 3 part video series I show you a step by step on building this project as well as talk about the modifications I had to make. The Article and plans ca...
Read this entry »
07-01-2009 06:32 PM
by Andy |
23 comments »
Updated 1/15/12
Now we need to cut a recess in the lid for the medallion to set down into.DONT cut your medallion until you have routed out the home for it.I typically make the medallion about 1” to 1.5” smaller on all sides than the lid depending on the box size and the piece of wood I have for the medallion.
We are now going to make a simple jig for a router to set on and run back and forth making several passes of incrementally deeper cuts. There are a several ways to do ...
Read this entry »
06-30-2009 04:42 PM
by Andy |
11 comments »
Updated 1/15/12
Regarding wood movement:Depending on the wood you use, where you live, and your own personal experience,y ou may want to allow more clearance.This is what works for me.
I really dont allow for any movement at this stage. I know this sounds like trouble waiting to happen, but it works just fine for me. Even if we start off with a snug fit, we will still end up with a small gap around the perimeter. This is due to the final sanding and easing of the edges between lid and l...
Read this entry »
06-24-2009 08:58 AM
by scrappy |
11 comments »
I have been asked to do a tutorial on how I made my Box Joint Bracelet
I will be trying to go Step-By-Step and not leave anything out. I know I am missing a couple of pics but will try and explain things as good as I can.
The first thing I would like to address is SAFETY There are many ways to do almost any process, depending on how you were taught/learned. Please be VERY carfull when useing your tools. I would hate to see anyone get hurt.
Onward: I only used one piece of wood f...
Read this entry »
03-26-2011 11:07 PM
by Lockwatcher |
3 comments »
NOTE: I have just edited this blog to make some corrections in the original text!
I have begun building my last (?) Easy Shop Table. Based on a similar design used in my Assembly Table from Wood Magazine (March 2010). Once again, this table (like my others) is built from standard grade construction lumber, redimensioned for the project (from the big box store). So far, I’ve purchased 2 2×10”s x 10’ for the frame of the project. The lumber cost for the frame assem...
Read this entry »
12-20-2011 03:57 AM
by DarrylF |
11 comments »
Hello everyone, a few people have asked me for plans on how to build the folded slotted chair I made so I decided to give it my best shot to measure the pieces and give a description on how it was done, so here we go.
Wood Used: Ash
Parts List:1 1/2” x 3/4” x 48”: 21 1/2” x 3/4” x 38”: 21 1/2” x 3/4” x 36”: 71 1/2” x 3/4” x 34”: 21 1/2” x 3/4” x 15 3/4”: 91 1/2” x 3/4” x 6”: 12
...
Read this entry »
03-20-2011 11:56 PM
by AlexHarris |
25 comments »
A video showing how to make some really good wooden bar clamps.
End your clamp shortage now! Build some clamps which only cost a few pounds to make and could be better than clamps you can buy.
These clamps don’t mark the wood or stain from glue.
Read this entry »
1 2 3 4 ... 95
next »
945 entries