LumberJocks

Woodworking blog entries tagged with 'leg vise'

  • Advertise with us
View HokieKen's profile

Building my Workbench #12: Leg Vise

07-10-2017 01:11 PM by HokieKen | 6 comments »

Well, over the past week, I did manage to get the leg vise mostly done. At least as “done” as I’m going to until the final assembly is done. I had already cut the mortise for the parallel guide before drawboring the leg. So next thing I did was to make the parallel guide and cut my chop to rough shape. The guide is made from a piece of cherry and the chop is the same gnarly Walnut I used for my end vise. I cut a blind mortise in the chop for the guide and drilled and ...

Read this entry »


View Mauricio's profile

Workbench Build - Splayed leg French Bench #16: Leg Vise Part 1

12-22-2012 02:51 PM by Mauricio | 25 comments »

Welcome back to my blog series folks. Thanks for following along on this long journey of mine. It’s hard to believe I started cutting up the parts for my top in January. It’s taken me almost a year. However there were some detours taken along with way on other project. I’m in the home stretch now! I needed a hub for the screw. One of the luxuries of making your own screws is that you can make the hub out of any wood you want. I went with some QSWO I had left from my stretchers. I think ...

Read this entry »


View Woodknack's profile

Farm Bench Leg Vise #2: Brace & Mayne Workbench & Vise

11-24-2014 05:41 AM by Woodknack | 1 comment »

This workbench is more primitive but carries the same angle brace leg vise mentioned in my previous blog post. Found in Farm Shop Work: Practical Manual Training, by George M. Brace and D. D. Mayne, 1915. http://thewoodknack.blogspot.com/2014/11/another-farm-workbench-with-angle-brace.html

Read this entry »


View Dave's profile

Roubo Workbench #4: Ch3 - Crossed Up

07-11-2014 07:13 PM by Dave | 0 comments »

After the success tweaking the installation for the end vise I hoped the good karma would continue to the leg vise. Not so… It All Starts With A Small Bonk… I removed my chop from the clamps, removed the glue and jointed/planed to size. the final size was about a 2 3/8 thick – plenty. I determined the centerline of the chop and leg and clamped the chop directly to the leg. I transferred the hole locations to the chop. The it was off to the drill press. Simple. While at Marc Adam...

Read this entry »


View bearkatwood's profile

The last piece of the puzzle.

01-20-2016 12:55 AM by bearkatwood | 11 comments »

So for my big remodel I had ordered a Galbert travisher, soss hinges and fancy drawer handles. I ordered all the fixins’ from benchcraft to make my bench. I saved up lumber for over a year to make it. Today I received the last piece of the puzzle to finish off the remodel and have a kick-butt beautiful place for me to make videos, play with designs and spend the rest of my life working on a craft I hold very dear and am hopelessly addicted to.John Switzer from Black Bear Forge in Beulah...

Read this entry »


View TheFridge's profile

building a bench and stuff #4: Beginning of the leg vise

05-23-2015 03:52 PM by TheFridge | 2 comments »

I milled the leg and spacers/support block out of the same chunk of oak. The screw and nut are the remnants of what I bought for my end vise. A cove cut on the table saw and an 3/8” round over gave me the basic profile. I smoothed it out of with a whatever rasp and file I had on hand. Then marked and mortised for the nut. I’ll probably put a dab of epoxy on final assembly of the nut to make sure to hold it captive. It’s damn good fit if I say so myself. ...

Read this entry »


View RaggedKerf's profile

My First Workbench #24: Day 24: Starting the leg vise.

09-12-2012 03:30 PM by RaggedKerf | 0 comments »

To view the post with pictures, please click here. Had to start sometime I guess! I didn’t do a whole heck of a lot. More like prep work, I figure. First, I took my 1×6 plank of pine and cut two 36” lengths. The bench is just a hair over 36” tall so the vise will be just off the floor. Next, I drew out the design I wanted. Nothing too fancy, just a slight curve (I drew it without a compass or round object) and a few straight lines. I decided since I will b...

Read this entry »


View Eric's profile

Roubo Workbench #4: Which Vise Do I Nurse in My Bosom?

06-22-2009 04:11 PM by Eric | 13 comments »

Bear with me. It’ll make sense eventually. I’ve got two vise screws. One was generously donated by a “homeboy” from the Porch, Bill Taggart, when I visited his place a couple few years ago. The other was a $10 eBay purchase. I’m trying to decide which one to use in my leg vise. Allow me to present the two candidates, and then leave your verdict in the comments below. Candidate A is a standard metal vise screw. I dunno, looks like about an inch or so thick, ...

Read this entry »


View Jeremiah's profile

Balanced Work Bench #2: building the leg vise

07-18-2013 03:38 AM by Jeremiah | 0 comments »

i have never made a leg vise before and i have no idea what to expect with the one i made. The basic concept came from Shop Notes. And i like the basic concept. However, i do NOT like the price of ACME Rod, ACME nuts or ACME ANYTHING. so i went with “off the shelf” 3/4” threaded rod from LOWES. I dont know if this will bite me in the butt or not. But just in case, i built the vice so i could change it out if i need to use a better threaded rod. The dimensions ...

Read this entry »


View RaggedKerf's profile

My First Workbench #27: Day 28: Leg Vise chop final touches

10-19-2012 10:23 PM by RaggedKerf | 0 comments »

To see the version with all the pictures (there’s a lot!) click here. I am forcing myself to finish this dadgum leg vise. I’m tired of seeing the parts sitting around and now that I’ve pretty much caught up with all the random tasks associated with the bench to get back to the next to last big project (last will be the sliding deadSven). I spent a little time touching up the beveled edges and getting things where I think I’m at as far as I can push my skills and...

Read this entry »


« prev 1 2 3 4 5 6 next »
51 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com