LumberJocks

Woodworking blog entries tagged with 'incra'

  • Advertise with us
View PurpLev's profile

Router Table #1: Design ideas, need some feedback

02-18-2009 09:44 PM by PurpLev | 43 comments »

OK, so yeah – another blog about a router table, but since I’m going to make one , might as well document it while I go, maybe someone can benefit from this. I’ve had a Rockler router table top + plate + fence which I got when I bought my router (Bosch 2 1/4hp). It had the misfurtune of being on the floor when my basement was flooded a couple of years ago, so that top was ruined. I since have been planning to replace it with a shop-built version, and make a full enclosed ...

Read this entry »


View 559dustdesigns's profile

Router Table Cabinet

09-24-2009 11:06 AM by 559dustdesigns | 26 comments »

This is a router table I’m working on for my shop. I was able to incorporate most the features I needed and plan to use it often. It isn’t finished but most the major parts are in place. I purchased the Incra twin linear, router table top, woodpeckers router lift and the porter cable 7518 motor from Woodpeckers Inc back in 2002 or 2003. Finally, she’s in working order. Since the last post I was able to complete the rear ...

Read this entry »


View StumpyNubs's profile

The Stumpy Nubs Workshop #28: Our homemade router lift sure beats bending over, and Randy touches poo!

10-31-2012 07:45 PM by StumpyNubs | 25 comments »

The “great particle board build off” that’s captivated the woodworking world is progressing nicely, but Stumpy takes some time off to make a router lift that just might save the universe! Then he chisels away at the confusion surrounding what types of tools people should own, does a tool review, and gets Randy to touch dog poo. That and a lot more on the new, exciting, action packed and informative episode of Blue Collar Woodworking! After you watch this one, visit St...

Read this entry »


View Blake's profile

My New Router Table #8: A Proud Moment

12-04-2007 03:07 AM by Blake | 24 comments »

So, No more messin’ around! Its time to cut the hole! With my template all biscuited and glued up, I shaved off the other half of the biscuits and sanded everything flat. With a little sanding and shaving off the inside I got the router plate to fit perfectly inside. So I decided to use my fabricated router plate template to make a one-piece template. This way I could also test the accuracy of it. So I sandwiched together the template, one solid piece of plywood which would be the...

Read this entry »


View PurpLev's profile

Router Table #12: The Good the Bad and the Ugly... New Fence Arrived

01-31-2010 02:07 AM by PurpLev | 22 comments »

I saw an ad on craigslist for a Jointech 12” router fence positioner which is similar to the Incra LS positioner -has a lead screw, and has what Incra sells as add on – the “wonder fence” as the standard fence. the guy posted it as used, but at what Jointech is selling it NEW… I contacted the person trying to negotiate a win-win situation. that was 2 weeks ago. the jointech fence is still on craigslist. I just couldn’t justify his price for a fence I’...

Read this entry »


View Ocelot's profile

Equipping the Shop #3: 1961 Craftsman RAS with added crosscut stop rail

04-17-2011 06:43 PM by Ocelot | 21 comments »

Finally, I’ve pulled the photos from my camera. I neglected to photograph it as I built it, but here it is in finished form. It gives me 8’ of stop range for precisely measured crosscuts. I can use it for through cuts as well as crosscut dados. The extension table top and fence are made of a partial sheet of 18mm (3/4”) oak veneer plywood that I’ve had laying around for 10 years or so. The legs are of ordinary 2×4 stud material. There is no finish on it...

Read this entry »


View degoose's profile

Open weave Lazy Larry #6: A crosscutting video...

07-21-2011 05:12 AM by degoose | 21 comments »

No explanation required… just watch.. Here is the dry fit after all the pieces have been cut… I did not show the cutting of the background Huon Pine peices .. I figure you know how this was done…. all cut at the first stop.. and again keeping them in order for grain flow…

Read this entry »


View PurpLev's profile

Router Table #9: Drawers, Bits, and a little Playtime

01-17-2010 07:36 AM by PurpLev | 19 comments »

Had some shop time today with 42 degrees outside, it was quite a lovely day. my compressor came back to life also – I guess when it goes below 40 the air is too thin for the compressor to be able to raise the pressure in the tank. I also got the radiant heater from Lee Valley. Last time around, by the time I decided to order it- they were out of stock, and just received new stock this week. it works well, not as well as I was hoping for, but decent. To turn it on/off you have to yank...

Read this entry »


View David's profile

Crosscut Sled

01-22-2009 08:13 AM by David | 19 comments »

This video features a new crosscut sled built for my shop. Inspiration for this sled came form books in my library and countless Internet searches. This is a simple project for the shop that will increase safety, speed and accuracy of crosscuts on the table saw. Construction is simple with a MDF base, maple fences, Incra Miter Bars and T-Track. The plan file is available for download. Hopefully this will inspire a sled for your shop! David STOP BLOCK DETAIL FRONT FENCE DETAIL

Read this entry »


View degoose's profile

Tool Gloat #3: Unilift.

12-14-2010 11:51 PM by degoose | 17 comments »

I just go my new toy yesterday… the Woodpecker Unilift router lift… from Graeme down at Professional Woodwork Supplies in Melbourne… Posted Friday… delivered Tuesday… good service from Australia Post…i will be attaching my Makita 3612 since I really don’t need a variable speed router for the table.. Included in the package were some Whiteside routerbits that Graeme recommended I use with the LS 17 Positioner router fence I got last week at Carb-a-t...

Read this entry »


1 2 3 4 ... 7 next »
67 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com