LumberJocks

Woodworking blog entries tagged with 'gluing'

  • Advertise with us
View lethentymill's profile

The Non-Electric Chair #14: Making the Chair (The back frame gets glued up and the chair comes together)

04-09-2009 11:07 AM by lethentymill | 3 comments »

There are some jobs that must be done as you go along; they will be very difficult to do once the back frame is glued up.Unfortunately, I am one of those people who must see results and can’t wait indefinitely to see a frame going together. Apart from the fact that I think someone said “A decision deferred is a decision well made” I have two excuses for this less than grown up behaviour.a) Sanding every square millimetre can be pointless if it turns out that there is a final curve or detai...

Read this entry »


View dustbunny's profile

StrongHand Clamps

08-03-2009 01:53 AM by dustbunny | 7 comments »

I was looking for a clamp that could hold a glue up of two 45 deg strips of wood to make a block. Basically two triangles glued together to make a square. All the woodworking site searches produced nothing. Then I came across these clamps on a welding website. http://www.stronghandtools.com/products/pdt_img/pgv_pic.html I ordered three of them from my local welding supply store to see how they would work. The man at the supply store had never seen them, apparently they have a patent...

Read this entry »


View sras's profile

Mahogany Kitchen Stool Project #3: Preparing Lamination Strips

02-12-2010 07:44 AM by sras | 9 comments »

There are three curved parts in each stool. These are formed by gluing up thin strips to create a thicker laminated part. The three parts are: 1. Seat Back – 7/8” thick (formed with 5 or 6 strips)2. Back Rest – 7/8” thick (formed with 5 or 6 strips)3. Slats – 3/8” thick (formed with 3 or 4 strips) (5 per stool) As I plan the construction, I start to realize that I have 6 stools with 7 curved parts each. That works out to 42 glue ups. Each one requires...

Read this entry »


View Rafe Demers's profile

Question /Gluing solid wood panels

05-14-2014 06:26 PM by Rafe Demers | 2 comments »

I am currently working on a Jewlery Box and had some questions. I will be making the box out of Sapele with a bookmatched Birdseye Mapel panel for the top which will be held in a dado/groove. The bottom panel will be Sapele and secured the same way. The corners will be mitered with Wenge keys to help strengthen the joints. My question is should I glue in the bottom and top panels? The top and bottom panels for the box will be about 1/4 inch. I know that when making cabinet doors in the past I...

Read this entry »


View Angela's profile

TV Stand #6: Finally gluing up the top

09-02-2011 03:19 AM by Angela | 1 comment »

I last left off where my boards for the top where seriously warped. I also was waiting for my new jointer. I received my new Powermatic Jointer and I love it. I wish I knew how to use it better but it will come in time. Jointing ProblemOne question I wondered about it when I tried to flatten a board. I jointed just one side of the board until it was flat. The only problem was to get the board flat the jointer removed so much wood that I wasn’t able to use the board because it became to...

Read this entry »


View kevinw's profile

Contemporary Cross project #3: Initial cuts of interior parts

11-29-2010 02:48 AM by kevinw | 0 comments »

We are now ready to begin sawing out our components. By hot gluing the two boards together this allows us to cut two identical pieces of each part so that they will fit properly. Note that I am only sawing out the interior shapes of the cross at this point. This will allow me to have better control when re-gluing. Here the vertical piece has been cut out. Keep in mind that you must get the best cut possible. Be sure your blade is narrow enough that it can saw the curves without backing up ...

Read this entry »


« prev 1 2
16 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com