LumberJocks

Woodworking blog entries tagged with 'glue'

  • Advertise with us
View yuridichesky's profile

Workbench #6: Leg vise chop

09-21-2013 05:43 PM by yuridichesky | 8 comments »

The leg vise chop’s wood is beech (I just have one big thick beech board and so I use it when I need some hardwood). .First some rough cuts: .Then cleaning up: (you can see here template I used to mark curves of the chop) (and this is my cleanup kit) .Ready for parallel guide mortise: .Parallel guide mortise: first saw cut then cleaning with the chisel (and a block of wood as a guide). .Dry fit: .Drawboring: .Closeups of drawboring results:...

Read this entry »


View twobyfour16's profile

Workbench #5: Trestle Base Complete

04-29-2012 05:56 PM by twobyfour16 | 7 comments »

Time to glue up. Since I painstakingly fit each tenon to it’s matching mortise, I was fairly confident that glue-up would go ok. To solve the short clamp issue, I went down to the hardware store & got some couplers to hook pipes together to get more length out of my pipe clamps. Also, I borrowed some longer parallel clamps from a friend – and I’m glad he had them! I did a dry assembly & everything worked great. It was a little tricky to do by myself, but I g...

Read this entry »


View Grumpy's profile

How to Transfer a Photo to Wood

12-12-2016 11:07 PM by Grumpy | 13 comments »

I like this idea. This type of project would make great Christmas presents..View on YouTube

Read this entry »


View Smitty_Cabinetshop's profile

Wall Hung Tool Cabinet #10: Backside of a Carcase

05-02-2012 03:55 AM by Smitty_Cabinetshop | 24 comments »

EDIT: Updated to eliminate BP BS. Smitty Whatever was selected for the backing material of this cabinet needed to add strength, look good and be 1/2” thick. Plywood meets two out of three of those requirements, but I just can’t fall in love with the idea of plywood in my tool till. Biggest hurdle with any other material is the work I might have to do to get it to that 1/2” thickness. I checked the remaining inventory of poplar (says Don W, and he should know) boards sa...

Read this entry »


View Tomato's profile

15 Ft Power-Drifter Fishing Boat, "Tiger Lily" #1: The plans are in!

01-15-2016 08:42 PM by Tomato | 5 comments »

Entry on 1/15/2016: Hi everyone! I am an avid steelhead fisherman in Southeast Michigan. The rivers down here are a little difficult to drift a float like I would prefer. It’s hard to get into a good hole due to lots of overgrowth on the banks and the majority of the river being private property. My solution is the Power-Drifter from Glen-L. It will allow me to slow my travel down the river, hotshot, fly fish, or drift with a spinning combo or centerpin. I will also get some good ...

Read this entry »


View tyskkvinna's profile

Videos #5: Glü Bot

07-09-2012 04:59 PM by tyskkvinna | 16 comments »

In this video, I am doing a small demo on FastCap’s Glü Bot along with Chris. FastCap is a recent new sponsor of ours and we have done a couple of videos showing off their cool stuff. This is the first!

Read this entry »


View CaptainSkully's profile

Arts & Crafts Dining Room Set #21: Dry Fit!

09-02-2010 04:21 PM by CaptainSkully | 3 comments »

I found another day off, so I immediately ran out into the shop before I could get distracted. I was able to finish the joinery on the base ends. As with everything else in life, the relative ease of the BeadLock Pro has disadvantages in repeatable accuracy. I don’t know how or why, but I do eight mortises and they only come out within 1/16” of each other. This has caused a 1/8” difference between the mortises, pretty much ruining my reveal on the spindles. I’ll f...

Read this entry »


View CaptainSkully's profile

Arts & Crafts Dining Room Set #20: Joinery Shortcuts

08-21-2010 04:12 PM by CaptainSkully | 1 comment »

I was able to squeeze another good day in the shop around work. I ran off to buy some more oak, then got home and planed enough of it down to glue up the stretchers/aprons for the table ends. While the laminations were cooking, I decided to give the BeadLock Pro a whirl. Having made integral tenons with chiseled mortises, and loose tenons with the router, I have to say this method is considerably easier and faster. First, I was able to cut off the parts to their finished length, without...

Read this entry »


View A Slice of Wood Workshop's profile

Scrap Wood Project- Candy Coffin Dish

10-30-2014 04:52 PM by A Slice of Wood Workshop | 4 comments »

Just in time for Halloween! Build this easy made candy dish in the shape of a coffin. after your base is in it’s final dimension (measurements included in video), there is no more measuring-even with the different angles. Check out the video and see how it is made. Please subscribe for more woodworking videos AND blacksmithing videos. And if you want to watch some nonprofessional welding, watch this video below as I create a skeleton out of some scrap metal around the shop.

Read this entry »


View pappyjohn's profile

Squirrel Ferris-Wheel feeder

04-21-2008 02:08 AM by pappyjohn | 6 comments »

Hello All, Here’s a couple of photo’s on the upcoming Ferris-Wheel Feeder for the Squirrels. This set of eight seats will be attached to a rotating ring with hangers for the seats to rotate around. The idea is once the squirrel gets on then they will rotate to the bottom. If they climb up the seats then they’ll continue to rotate down to the bottom of the revolving wheel. The size of the seats are approx. 6 1/2, 2 1/2, by 1/14they are made of some small pieces o...

Read this entry »


« prev 1 2 3 4 5 6 7 ... 10 next »
97 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com