LumberJocks

Woodworking blog entries tagged with 'galoot'

  • Advertise with us
View Steve Diogo's profile

New appreciation for hybrid woodworking

03-29-2014 08:04 PM by Steve Diogo | 8 comments »

Just finished ripping a 5-foot 2×4 for an artist’s easel, and Holy Crap was that a workout. I’m hella proud of the straight cut, but I think I have a new appreciation for the hybrid approach. It’s enough to make a guy want to break out the credit card for a table saw, but I like my marriage too much. Got the one piece ripped and dressed, but I think that’s enough for today. The second one will have to wait. I need a nap.

Read this entry »


View scruboak51's profile

Becoming a Galoot #5: Falling off the Wagon

01-28-2014 01:54 AM by scruboak51 | 2 comments »

I have to start by thanking others for the advice given in my last post. I put a new edge on my planing blade, getting it hair shaving sharp, and adjusted the depth to take a very thin slice. While not smooth as butter it was a tremendous improvement over my initial attempts. However, I also admitted defeat in my attempts to make this a hand tool only project. There were a couple reasons for this. The last foot (.3 meter) of the surface took a pretty nasty dive; a bit over a half an ...

Read this entry »


View scruboak51's profile

Becoming a Galoot #4: Planing Blues - In Need of Advice

01-25-2014 08:46 PM by scruboak51 | 4 comments »

Things have progressed nicely over the past few days. After a good 30 minutes of study, I laid out some chalk lines to square up the live edges. Then went to work ripping with a combination of the old cross-cut and a small rip-saw on the sections that were thin enough for that to be effective. It’s about time put a fresh edge on the old crosscut. Things really started bogging down during these cuts. I was able to muscle through, and am pretty pleased with how the projec...

Read this entry »


View scruboak51's profile

Becoming a Galoot #3: Finally Apart

01-24-2014 01:29 AM by scruboak51 | 3 comments »

After getting a nice deep and clean line to follow, I decided to stand this log on end to finish the cut. This was the most challenging aspect of the whole thing; as it’s got to be a good 250+ pounds (113 kilo’s) of deadweight. I resorting to using the car jack and some wood blocks to get one end as high off the ground as possible; then I use good old fashion muscle. Once upright, I walked it over to a support beam and threw some clamps on the help hold things steady. ...

Read this entry »


View scruboak51's profile

Becoming a Galoot #2: Jumping in the deep end

01-23-2014 04:49 AM by scruboak51 | 1 comment »

To the saw mill, or not to the saw mill; that was the question I left off at in the first post of this series. Saw Mill Cons Expensive $125 Hr, Plus $50 for blade breakage (Southern California Prices) Far Away – 1 hour drive in a truck that is on “hospice” A few weeks of waiting Saw Mill Pros Has done nice work for me in the past Would get all my cuts done with 0 effort on my part (just money) One thing I noticed was some of the cracks in this contain...

Read this entry »


View scruboak51's profile

Becoming a Galoot #1: Testing the waters

01-23-2014 04:04 AM by scruboak51 | 2 comments »

I was fortunate enough to stumble across a sizable piece of redwood root system at my local thrift store. The owner buys storage lockers and he got in a huge haul of redwood. After buying a gem of a slab of Buckeye Burl, I had my eye on this piece and hoped it was the right combination of big, dirty and in the way that would necessitate a price drop. As luck would have it, a month or two of waiting allowed me snag this for $50 It’s heavy; probably 250 pounds (113 kilos) and ...

Read this entry »


View RGtools's profile

Hand tool tips and tricks #20: A Bit More About Resawing

04-24-2013 01:16 PM by RGtools | 1 comment »

Generally the aim of resawing a piece of wood s to divide in neatly in half. One thing you have to account for is the kerf of the saw. If you place a line dead center, one side will end up thinner than the other. For this reason you can offset the line from the center by the width of your kerf (this is a measurement you will be able to eyeball with some ease after converting a couple hundred yards of wood into sawdust). It occurs to me that I should have taken some photos of that layout p...

Read this entry »


View jjw5858's profile

Exercises in Artisanship #31: The Woodrights Galoot library Part 2

10-25-2012 09:40 PM by jjw5858 | 6 comments »

What, no spoons you might be thinking…lol. Well of course not for it is time to get grooving with our Woodrights Galoot Library! No matter what you do sometimes the wood has made up it’s mind on how well it will work for the job. In this episode the old box store pine was what I call a bit “Bitchey”,.....not sawing so well, and especially not up for me having an easy go of dadoing the inner sides. The tools were all plenty sharp but the wood was just a little tough and sappy this tim...

Read this entry »


View RGtools's profile

Occasional Table Class (Hand Tool Build) #25: The Home Stretch

04-11-2012 02:15 AM by RGtools | 21 comments »

Once you have taken the clamps off of your base and your top you are in that dangerous period I think of as the home stretch. It’s easy to want to run into it. Stop. Sharpen all your tools. Breath. Think…then get back to work. Trust me, if all your tools are sharp and you are in the right mindset this phase of your work will be the most uplifting in your shop; it will be the time you breathe life into your furniture. If you are ill prepared for it you can make frustrating mistakes. Start b...

Read this entry »


View daltxguy's profile

How to make a glut

01-14-2012 09:36 AM by daltxguy | 11 comments »

This is entirely the method shown by Roy Underhill but with color pictures and timbers which he has probably never worked with. What is a glut? A glut is a wooden wedge used to split timbers green from the woods.Made from wood, to split wood! Made entirely with a handsaw and an axe. Start with about a 2’ section of log 4-5” in diameter. This is my SUV carrying it back from the woods.Here I am use Australian Blackwood. I have about 50 of these dead standing ones which ...

Read this entry »


« prev 1 2 3 4 next »
35 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com