LumberJocks

Woodworking blog entries tagged with 'fitting'

  • Advertise with us
View DustyMark's profile

Building a KARA Hummer Layout Duck Boat #26: Sewing the Dog Blind

09-18-2015 02:12 AM by DustyMark | 6 comments »

Overview I’ve only sewn for a week now and getting this dog blind right was quite the challenge for a rookie like me. However, I eventually prevailed! My goal was to establish a good profile that would hold even after adding the Avery Killerweed. Modeling The blind has a complex shape, so I did some modeling to establish a pattern. I began with the actual material draped over the frame, but this wasn’t very helpful. Copper wasn’t too excited about getting ...

Read this entry »


View andyboy's profile

student dovetails #4: Student progress dovetailing.

08-15-2014 08:12 AM by andyboy | 2 comments »

http://youtu.be/nE9ayin-vXQ Really proud of the determination my students have shown learning this skill.

Read this entry »


View CueballRosendaul's profile

Finished the replacement spindle in time for Christmas

12-31-2013 09:51 PM by CueballRosendaul | 3 comments »

A few weeks ago, I asked about fitting a replacement spindle into an old rocker without disassembling it. Here’s how it went: I took a picture of the spindle next to the missing one with my tape measure held along side it. This gave me a scale that I could duplicate by printing the picture out so the dimensions matched. I printed two copies, took one and cut it out completely to tape it to the tool rest on the lathe. The other one I took measurements at critical points with my calipe...

Read this entry »


View DustyMark's profile

Building a Dr. White's Chest #8: Hanging Doors

05-07-2013 12:01 PM by DustyMark | 0 comments »

Mortising the HingesHanging doors involves a mixture of precise work and some trial and error. The first step is to choose a hinge and then mortise the case frame to receive the hinge. A common approach for hinge placement is to locate the top of the upper hinge even with the bottom of the upper rail and locate the bottom of the lower hinge even with the top of the lower rail of the door frame. I should have thought ahead and routed these mortises before assembling the case. However, I fo...

Read this entry »


View PurpLev's profile

Machinist Toolcart #13: Finishing Touch

09-16-2011 03:39 AM by PurpLev | 3 comments »

After realigning the drawers by fixing the slides, and trimming some drawers, I made sure everything fits. I predrilled 3 holes in the drawer fronts through the pull slots that will later be covered, one in the center, and 1 on each side: I transferred the center hole from the drawer front to the drawer and once alignment was satisfactory I transfered the other 2 holes as well: I used my combination square ruler to space the fronts from each other, and made sure that all the dra...

Read this entry »


View PurpLev's profile

Machinist Toolcart #12: Spoken Too Soon: A Lesson in Drawer Planning/Measuring/Fitting

09-13-2011 04:22 AM by PurpLev | 5 comments »

As I was fitting the drawer fronts yesterday I noticed that the fronts are being located with their bottoms pretty much aligned with the bottom of the drawers which made me think – shouldn’t there be some overlay there? but I digressed and went on about it…. Looking back – I guess there should have been an overlay after all! See, when I originally planned the drawers I setup a (from the bottom) 6” drawer followed by 2 5” drawers … and each drawe...

Read this entry »


View Tim & Candy Hicks's profile

Juniper Log Furniture : Floor Lamp #4: Still scribing

05-26-2009 08:47 PM by Tim & Candy Hicks | 0 comments »

Getting closer to where we want to be

Read this entry »


View David's profile

Steamed Cherry Display Shelf

05-13-2007 04:24 AM by David | 13 comments »

I thought I would share the progess of a couple of cherry display shelves being built for some close friends in Central Oregon. This will be used to display works of art in thier gallery. I am using steamed cherry and pocket screw construction. This a follow up from a previous post on using the Kreg Pocket Hole Jig system. I am taking a break from work and the shop spending Mothers Day weekend in Sisters, Oregon. Final sanding and finish await me at home. Cherry top with first coat of tung...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com