Woodworking blog entries tagged with 'fine woodworking magazine'

  • Advertise with us
View HappyHowie's profile

Trestle Table #6: Complete Cambered Cauls

09-04-2016 10:29 PM by HappyHowie | 2 comments »

After using my planer yesterday to cut the cambered ends, I drilled holes two inches in from the ends of each caul. I selected a 3/8” drill bit in order to easily fit the 5/16 diameter bolts I purchased yesterday. Besides laying the bolt on my bench and testing the thickness of a 5/16” and a 3/8” drill bit along side the bolt, I also drilled a test hole in a scrap board. I selected my 3/8 inch drill bit for my cambered cauls. After marking a line two inches in from ...

Read this entry »

View HappyHowie's profile

SawStop Assembly #6: Making Van Dyke's RIP Fence JIG

05-15-2016 05:57 AM by HappyHowie | 0 comments »

I finally got some time today, Saturday, to work on this Rip Fence JIG. The trickiest part is done: the DADOes. The photo shows the dry fit. Before I glue these parts together I will drill the countersinks, holes, etc. I will start that tomorrow.

Read this entry »

View HappyHowie's profile

Rocking Chair: An Online Course #15: Loose Tenons: Festool Domino or Mortising JiGs

04-03-2016 07:11 AM by HappyHowie | 3 comments »

While viewing the rocking chair instruction, Tom McLaughlin stated that he used a three-slot router bit to make his mortises on the chair’s back legs and the corresponding rockers and crest rail. That method was used for his first rocking chair. However, when he went to Tommy Mac’s Rough Cut show they used instead Tommy Mac’s Festool Domino mortising machine. They cut the mortises with his machine and then placed Festool’s loose tenons in them. Festool calls these ...

Read this entry »

View HappyHowie's profile

Miniature Bench #2: Legs with Feet and Mortises for Clamping to Main Workbench

02-03-2016 04:05 PM by HappyHowie | 0 comments »

LEGS CONTINUED.. My next steps were to make the legs for this mini bench. I had already glued the two plywood sheets together. I also had my cherry hardwood parts ready. I used a marking knife to define the the grooves I would cut in order to fit the plywood stretchers. The grooves would be very shallow, but enough to align the stretchers. I used a DADO setup to cut the grooves. I used test pieces first to define the depth. When I was satisfied with the saw blade depth setting I cut...

Read this entry »

View HappyHowie's profile

Miniature Bench #1: Steve Latta's Mini Bench Plan

01-30-2016 02:38 PM by HappyHowie | 0 comments »

With my sore back, I needed a solution when working at my workbench. Clamping a mini-bench seems like a good step to take. Of the plans I have seen I like Steve Latta’s miniature bench that was presented in Fine Woodworking Magazine. I bought the plan and printed the article. The reason I like it is because along the working edge of the bench, the legs are flush with the benchtop. This allows the user to clamp boards, etc to the side of the mini-bench. I had most of the lumber al...

Read this entry »

View HappyHowie's profile

Hardwood Store

01-12-2016 02:56 PM by HappyHowie | 6 comments »

Yesterday I went shopping for hardwood. In this state I am only aware of two hardwood lumber stores: MacBeath Hardwood and Intermountain Wood Products. At MacBeath’s the customer can walk into the storage area and pick out anything that fits his fancy. It is different at IWP. There you state what you are there to buy, then a fork-lift operator will take your list and will bring out a pallet, one species at a time, so you can select the boards you want. Then he will make another t...

Read this entry »

View mafe's profile

Popular Woodworking Magazine (who have the rights?) is that really ok?

02-18-2011 09:00 PM by mafe | 67 comments »

Popular Woodworking Magazinebe careful with readers contributions, ‘Tricks of the trade’. Hi LJ’s. I have an experience I want to share with you; unfortunately I can’t say it was a good one, but not the end of the world either… All of you, who know me here on LJ, probably know I’m not a complaining kind of person. Some months ago I was contacted by Popular Woodworking Magazine (PWM), they asked if they could bring one of my posts here on LJ in the magazi...

Read this entry »

View Lee A. Jesberger's profile

Fine Woodworking does ezee-feed review #1: Finally some exposure

02-17-2008 03:40 AM by Lee A. Jesberger | 38 comments »

I just got this notice from notice from Roger Strautman!! From: Roger StrautmanSubject: Ezee-feed!!! Congratulations for getting into Fine Woodworking Magazine. That’s just great! Ihope that helps your sales. Good luck! ————————————————————————————————- This is great news for me as they...

Read this entry »

« prev 1 2 3 4
38 entries

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics