LumberJocks

Woodworking blog entries tagged with 'end'

  • Advertise with us
View JonasB's profile

Yet another workbench #1: My belt and suspenders design.

08-27-2015 10:35 PM by JonasB | 5 comments »

So I decided I needed to finally build a real woodworking bench for my new workspace. I got all the books by Chris Schwarz, checked all the back issues of woodworking mags and browsed the internet in preparation. Then the first thing I did was break one of Chris Schwarz rules. I decided to design my own rather then duplicate a historical bench. I think I had valid reasons. My workspace is small. I could not fit a long bench. A short bench means planning forces have a bigger impact, so I d...

Read this entry »


View CaptainSkully's profile

Darrell Peart's Aurora Sofa Table #1: In the Beginning...

09-03-2009 06:27 AM by CaptainSkully | 5 comments »

This is my most ambitious project to date. I’m going to make a Greene & Greene sofa table that closely follows the design of premier G&G LJ Darrell Peart. I pinged him the other day, and he sent me to American Furniture Design Co. to buy plans. As you can see, they’re not identical to the one made by Marc in Darrell’s class at William Ng's woodworking school. American Furniture’s Version: TheWoodWhisperer’s Version: What I plan to do i...

Read this entry »


View JonasB's profile

Yet another workbench #5: Hardware 2 and Wrap Up

08-31-2015 09:49 PM by JonasB | 2 comments »

Parallel guide chain mechanism To make the chain mechanism, I used #35 chain and the sprockets are 10T with a 3/8 center. The chain is attached using two chain links. I had to do some metal working to create a few items: the brackets to hold the sprockets and a way of securing the chain at both ends. I had a 1.5” rectangular steel tube in my scrap collection so I used an angle grinder with a cutoff wheel to make both brackets that hold the sprockets with 3/8 bolts. Big box store ang...

Read this entry »


View CaptainSkully's profile

Limbert Lamp Table - Stickley #240 #6: Final Glue Up & Finish

09-07-2009 11:44 PM by CaptainSkully | 11 comments »

At the urging of my girlfriend, I fumed a small scrap of QSWO and then went over it with amber shellac and dark brown wax, buffing it out with 0000 steel wool. It’s pretty magnificent. As a result, I decided to give my Limbert table an “authentic” Stickley finish. While waiting for the glue to cook, I fashioned what can only be described as an impromptu fuming tent. Even one of my neighbors came over to see what monstrosity I was building, as they’re usually ...

Read this entry »


View CaptainSkully's profile

Darrell Peart's Aurora Sofa Table #4: Table Top

09-08-2009 03:38 AM by CaptainSkully | 3 comments »

As I was waiting for another project to dry, I did a little work on the table top. I had cut it oversized on purpose to take advantage of the wavy figure in the board. I then had to face the difficult decision of how to trim it down for a sofa/foyer table that didn’t stick too far out. I settled on a 14” wide board, which leaves plenty of room for a decent overhand in the front, 2 1/4” legs, and a side apron that doesn’t look like a chubby baby’s leg. I the...

Read this entry »


View CaptainSkully's profile

Darrell Peart's Aurora Sofa Table #5: Breadboard Ends

09-08-2009 09:34 PM by CaptainSkully | 3 comments »

While I’m ammonia fuming another project, I figured I’d make progress on this one. I pulled a WoodWhisperer and threw away the tape measure. I milled the ends to the proper thickness (which also gave me some nice mahogany veneer). I can’t tell you how lovely working mahogany is, compared to oak. Then while the stock was still one long piece, I used the table saw blade to make the dado that fits the tongue on the top (Darrell calls it the “core”). I achieved ...

Read this entry »


View Tomato's profile

15 Ft Power-Drifter Fishing Boat, "Tiger Lily" #3: Took a break to build a work bench... check her out (Gallery)!

04-01-2016 03:32 PM by Tomato | 1 comment »

Found this at a thrift shop and restored it. (Just an old Stanley Two-tone Jack but works for now) My own knife, plane iron, and chisel sharpening system I designed. 80 to 7000 grit.

Read this entry »


View JGardner23's profile

What I'm Up Too!

09-22-2007 08:01 AM by JGardner23 | 8 comments »

ok well last weekend i was able to knock out most of my new workbench. Which is based on the New-Fangled one on FineWoodworking.comhttp://www.taunton.com/finewoodworking/ProjectsAndDesign/ProjectsAndDesignArticle.aspx?id=28530 i am also about to finish a desk i have been working on for some time now. here is a few in in progress pics Here is some pic’s of the workbench.

Read this entry »


View JonasB's profile

Yet another workbench #4: Hardware 1

08-30-2015 05:41 PM by JonasB | 0 comments »

Screw assembly The face vise screw mechanism is all DIY. Here are the piece parts. The hand-wheel has been kicking around my basement for 15 years. I remember buying it on Ebay for a project I never completed. It was too nice to throw away, so it waited and waited until now to find a purpose. The acme screw and nut I picked up on Ebay more recently. I cut the screw to length and drilled the hole that holds the hand-wheel setscrew. I found a 5 inch brass plate 1/2 inch thick also on...

Read this entry »


View A Slice of Wood Workshop's profile

2x10 End Table

12-24-2012 04:02 PM by A Slice of Wood Workshop | 1 comment »

I built an end table from a single 2×10. I wrote up a little post, but it’s too long to put over here. Click here to view the post.

Read this entry »


1 2 next »
20 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com