LumberJocks

Woodworking blog entries tagged with 'end'

  • Advertise with us
View CaptainSkully's profile

Limbert Lamp Table - Stickley #240 #8: Ammonia Fume Finish

09-12-2009 08:24 PM by CaptainSkully | 8 comments »

Well, after three days in solitary, I decided to pop the the weasel. The different boards fumed to different tones, but I think with shellac and brown furniture wax, it’ll be just non-perfect enough for some charm. The wood putty had no tannins in it, so it’s almost white. Luckily, one corner is perfect, so that’ll be the one facing out. I tried my Dark Fumed Oak aniline dye, and it didn’t work on the putty either. I even brushed the liquid ammonia directly on...

Read this entry »


View CaptainSkully's profile

Darrell Peart's Aurora Sofa Table #5: Breadboard Ends

09-08-2009 09:34 PM by CaptainSkully | 3 comments »

While I’m ammonia fuming another project, I figured I’d make progress on this one. I pulled a WoodWhisperer and threw away the tape measure. I milled the ends to the proper thickness (which also gave me some nice mahogany veneer). I can’t tell you how lovely working mahogany is, compared to oak. Then while the stock was still one long piece, I used the table saw blade to make the dado that fits the tongue on the top (Darrell calls it the “core”). I achieved ...

Read this entry »


View CaptainSkully's profile

Limbert Lamp Table - Stickley #240 #7: Fumearama

09-08-2009 09:11 PM by CaptainSkully | 9 comments »

After letting the glue cure overnight, I took it out of the clamps and gave it a final hand sanding. Not too bad, but could be better. I think next time I’ll err on making the legs touch on the outside corners instead of a flat meeting. This caused some gappage that I filled with putty. Since our dog laid down by the tent, I figured it was time to fume. There’s no better time than the present. I carefully put the tent over the table and then propped them both up en...

Read this entry »


View CaptainSkully's profile

Darrell Peart's Aurora Sofa Table #4: Table Top

09-08-2009 03:38 AM by CaptainSkully | 3 comments »

As I was waiting for another project to dry, I did a little work on the table top. I had cut it oversized on purpose to take advantage of the wavy figure in the board. I then had to face the difficult decision of how to trim it down for a sofa/foyer table that didn’t stick too far out. I settled on a 14” wide board, which leaves plenty of room for a decent overhand in the front, 2 1/4” legs, and a side apron that doesn’t look like a chubby baby’s leg. I the...

Read this entry »


View CaptainSkully's profile

Limbert Lamp Table - Stickley #240 #6: Final Glue Up & Finish

09-07-2009 11:44 PM by CaptainSkully | 11 comments »

At the urging of my girlfriend, I fumed a small scrap of QSWO and then went over it with amber shellac and dark brown wax, buffing it out with 0000 steel wool. It’s pretty magnificent. As a result, I decided to give my Limbert table an “authentic” Stickley finish. While waiting for the glue to cook, I fashioned what can only be described as an impromptu fuming tent. Even one of my neighbors came over to see what monstrosity I was building, as they’re usually ...

Read this entry »


View CaptainSkully's profile

Darrell Peart's Aurora Sofa Table #1: In the Beginning...

09-03-2009 06:27 AM by CaptainSkully | 5 comments »

This is my most ambitious project to date. I’m going to make a Greene & Greene sofa table that closely follows the design of premier G&G LJ Darrell Peart. I pinged him the other day, and he sent me to American Furniture Design Co. to buy plans. As you can see, they’re not identical to the one made by Marc in Darrell’s class at William Ng's woodworking school. American Furniture’s Version: TheWoodWhisperer’s Version: What I plan to do i...

Read this entry »


View CaptainSkully's profile

Arts & Crafts Night Stands #3: Some Assembly Required...

08-26-2009 09:22 AM by CaptainSkully | 4 comments »

Today, I took the rough parts and managed to achieve a few dry fits. The first one was to make sure the dadoes and tenons fit. The second one was to see how it looked with the bow cut out of the bottom piece and with the pre-finished panels installed. A couple of thoughts: be sure your table saw is waxed properly when cutting tenons like this. It helps if you don’t have to use force to push the piece through the saw. I realized I’m already using some of the stuff I learne...

Read this entry »


View CaptainSkully's profile

Limbert Lamp Table - Stickley #240 #1: Templates

07-15-2009 03:43 AM by CaptainSkully | 2 comments »

So, between TreeFrogFurniture.BlogSpot.com and Robert Lang’s book “More Shop Drawings for Craftsman Furniture”, I decided that the corner of our dining room could stand an accent table. TreeFrog has built two different styles, so I “borrowed” the plans for the one I liked (he posted them online) and made my first template. I’m going to wait to make the interior template until I have the shell complete. The angles make things a bit messy. Like Tre...

Read this entry »


View JGardner23's profile

What I'm Up Too!

09-22-2007 08:01 AM by JGardner23 | 8 comments »

ok well last weekend i was able to knock out most of my new workbench. Which is based on the New-Fangled one on FineWoodworking.comhttp://www.taunton.com/finewoodworking/ProjectsAndDesign/ProjectsAndDesignArticle.aspx?id=28530 i am also about to finish a desk i have been working on for some time now. here is a few in in progress pics Here is some pic’s of the workbench.

Read this entry »


View frank's profile

"A Brush Stroke of Illusion" --by RusticWoodArt

05-09-2007 01:18 PM by frank | 5 comments »

A Brush Stroke of Illusion ....at end of day, when all my world has had it’s say, and now i am giving these places in my heart, a time to settle down for a good nights rest…. —-comes the longing crisp of a brushes breath, and so i give the right to let the colors fly,while painting this wood with sealing stealth, where once again i impart a stop gap by and by…. —-wondering now i watch the dance, as brush gives color streams of pigment gloss, while who ca...

Read this entry »


« prev 1 2
20 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com