LumberJocks

Woodworking blog entries tagged with 'duck hunting kayak'

  • Advertise with us
View DustyMark's profile

Building the "Swiss Army Knife" of Small Boats...Wood Duck Double #56: Cockpit Shroud

09-09-2020 02:10 AM by DustyMark | 0 comments »

Amazing ResultsI’ve gone back and forth on how or whether to sew a facial shroud for the blind. The opening between the doors and the dog cockpit is slightly oversized so that I can paddle with the doors closed. I decided to give a shroud design idea that I had a try. I’m glad that I sewed a flap and a strip of velcro at the top front edge of the dog cockpit to hold the shroud. It was better to sew those in and not use them than to wish I had sewn them later. I was surp...

Read this entry »


View DustyMark's profile

Building the "Swiss Army Knife" of Small Boats...Wood Duck Double #55: Brushing the Blind

09-07-2020 01:53 AM by DustyMark | 0 comments »

Applying Raffia GrassI applied Raffia grass to the blind in order to give it some 3-D effect for a better hide. I bulk-ordered it from J.M. Stern Company a few years ago. I’m no expert, but here’s how I applied it to the blind. Here are the heaps of the four colors I used…green, light brown, dark gray, and light tan. That blend proved quite effective for me with a previous layout boat all season long without having to add natural vegetation. I tend to go ove...

Read this entry »


View DustyMark's profile

Building the "Swiss Army Knife" of Small Boats...Wood Duck Double #54: Blind Body: Dog Blind

09-03-2020 04:10 AM by DustyMark | 4 comments »

Lots of SewingThe dog blind was pretty complicated to sew. It’s 3-D shape, so it requires darts to shape it around the frame. View from the inside. There are eight buckles to hold it to the kayak, four buckles to support the decoy barrier, seven velcro sleeves to hold it to the frame, one buckle to hold the back door shut, velcro to hold the shroud at the front, a zipper, and brushing straps View from the outside. The door has .4” foam inside to give it some...

Read this entry »


View DustyMark's profile

Building the "Swiss Army Knife" of Small Boats...Wood Duck Double #53: Blind Body: Doors

08-30-2020 02:43 AM by DustyMark | 0 comments »

Floated the BoatWe floated the boat today with about the amount of weight it will have once the decoys are deployed. Mary sat in the boat as “self-propelled ballast” and I cut the side panel material of the blind at the waterline. That’s the waterline of the kayak loaded. Unfortunately, I ran 4’ short of binding edge material to even finish these edges. I totally messed up that order! Sewing the DoorsI draped a 2’ by 5’ piece of material over t...

Read this entry »


View DustyMark's profile

Building the "Swiss Army Knife" of Small Boats...Wood Duck Double #52: Blind Body: Base

08-29-2020 04:34 AM by DustyMark | 0 comments »

Designing on the FlyI pretty much “wing it” when I’m sewing blinds. My initial thought was to have the flip blind doors provide sole coverage for the middle third of the kayak. However, once I started sewing the stern panel, I realized I could extend it to the bow panel and provide a nice, fitted base for the blind that would provide better coverage with the Rafia grass. View of blind base from port bow. I’ll float the kayak with me and gear and Mary will pin...

Read this entry »


View DustyMark's profile

Building the "Swiss Army Knife" of Small Boats...Wood Duck Double #51: Blind Body: Boat Prep

08-25-2020 01:46 AM by DustyMark | 2 comments »

Backing PlatesI fabricated backing plates from 1/8” aluminum for use under the bimini mounts. I didn’t want those #10 washers pulling through the deck when I flip open a wet door! I also cut all the bolt ends flush under the deck with my Fein oscillating sander and the bimetal blade attachment. Clevis Pin Tethers I used 1/16” braided stainless cable to tether the clevis pins to the blind frame. Each tether is riveted to the frame. BucklesThe lower edge of t...

Read this entry »


View DustyMark's profile

Building the "Swiss Army Knife" of Small Boats...Wood Duck Double #50: Duck Blind Frame: Doors

08-22-2020 09:33 PM by DustyMark | 0 comments »

Complicated BendsBending the doors always kicks my butt. I used both ends of my conduit practice piece before I moved on to aluminum tubing. I’m laying pretty low in these pictures. There’s room for me to raise the seat up one incline notch. Once you get all your gear on, the extra room gets used up. I hate being crowded under the doors. I don’t need a framed face shield. A soft shroud attached at the roof of the blind will work just fine. I’ll part...

Read this entry »


View DustyMark's profile

Building the "Swiss Army Knife" of Small Boats...Wood Duck Double #49: Duck Blind Frame: Main Body

08-22-2020 04:08 AM by DustyMark | 0 comments »

DecisionsThis is the point in the blind build that you make basic decisions like how low to lay in the blind and how much room to set aside for decoys and the dog. My objective remains to paddle the kayak with the blind doors closed around my torso. This will allow an amazingly quick set up. This is a comfortable position for Copper and me. It’s the second lowest position on the layout seat. The lowest position would conceal us better, but at the expense of comfort. Copper i...

Read this entry »


View DustyMark's profile

Building the "Swiss Army Knife" of Small Boats...Wood Duck Double #48: Electric Bilge Pump and Stern Rudder Pedals

08-21-2020 03:32 AM by DustyMark | 0 comments »

Electric Bilge PumpI struggled over where to locate the electric bilge pump. Normally I mount them behind the stern seat and attach the battery to the aft side of the stern bulkhead in the stern hatch compartment. My initial thought was to mount it behind the solo seat so that I could keep the fish cooler as far back as possible. Here are the items I typically use for an electric bilge pump installation in a small boat. I was most of the way complete with building a pump system cent...

Read this entry »


View DustyMark's profile

Building the "Swiss Army Knife" of Small Boats...Wood Duck Double #47: Duck Blind Planning

08-13-2020 03:49 AM by DustyMark | 0 comments »

What Fits?Duck season starts in MN on 9/26…I need to build my blind! Now that I know Copper will be riding in the back, the big question is “how many decoys can I realistically fit in the kayak?” I’m able to squeeze a dozen full-size decoys between me and Copper and stay below the notional height of the blind. My blind bag and six decoys fit in front of my feet. I’ll wedge my shotgun and case on the floor on one side of the kayak behind me. IR...

Read this entry »


1 2 3 4 ... 6 next »
54 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com