LumberJocks

Woodworking blog entries tagged with 'drill press'

  • Advertise with us
View WoodJediNTraining's profile

Make a Folding Out Feed Table for your Table Saw

02-20-2013 05:22 PM by WoodJediNTraining | 17 comments »

This Week I show you how to make a folding out feed table for your table saw. This design was based after an article and plan found in a 2009 issue of Woodworker’s Journal Magazine. Originally the plan was designed for a Cabinet saw with a Biesemeyer Fence System, so I had to make some slight modifications for my Porter Cable Saw. In this 3 part video series I show you a step by step on building this project as well as talk about the modifications I had to make. The Article and plans ca...

Read this entry »


View OregonBurls's profile

How to find and harvest legal burls!

10-13-2009 05:44 PM by OregonBurls | 38 comments »

Hey everyone, It was suggested that I start a discussion on how to find and harvest burls. Please give your input also. I don’t deal with straight grain that often. I cut and sell burls for a living so here is what I know. It is illegal to harvest a burl without permission. of course if it is on your own property you can give yourself permission. What I do is put an ad on Craig’s list saying I want your burls. Most people don’t know what burls are. So you don’t get that many calls....

Read this entry »


View Jim Jakosh's profile

Murphy Bed #1: Building a Murphy Bed from scratch

07-10-2013 10:57 PM by Jim Jakosh | 42 comments »

We need a Murphy bed next winter in Arizona and I did not want to buy the hardware. That takes all the fun out of designing it yourself and costs $360. So I looked at a lot of bed designs and settled on one that used HD pivots, gas springs for counterbalance and a swing out leg support rather than the fold down kind.The parameters were a twin mattress (7×39 x 75), had to flip long ways and enough room inside for making the bed. Then I had to decide on the pivot points, the foot pivot ce...

Read this entry »


View Kent Shepherd's profile

Box Building #5: Barrel Hinge Installation

03-22-2012 09:50 PM by Kent Shepherd | 22 comments »

After showing some of my boxes in “Projects”. I have received some inquiries about the installation of the barrel hinges I sometimes use. I hope this helps for some of you. I know it will be overkill for many of you, so just use what you wish. With any type hinge, the layout is critical. These hinges are simple to install, but you must get your holes in the right place. If you don’t, I can assure you , you will not like the results, and you will not be able to go back and...

Read this entry »


View Brad's profile

To Shopsmith or Not to Shopsmith

07-28-2008 09:57 PM by Brad | 32 comments »

So I’ve been debating with my father in law about weather or not he should sell his Shopsmith setup invest in building a new shop using standard stand alone tools and machines. He’s about to retire and is kicking the idea around of either selling it or dropping another $1K into upgrading to all new Shopsmith stuff. Personally I’ve never used the SS but I sincerely doubt I’d be a fan. Not being able to move from machine to machine would bug the hell outta me and bein...

Read this entry »


View Lockwatcher's profile

Easy Shop Table - Planer Table #6: Adding the casters and finishing the project

04-03-2011 07:30 PM by Lockwatcher | 0 comments »

Well, my casters came in from my local Woodwerks store. Just as in previous entries, the casters are the most expensive part of this project. The casters I have been using lock both the wheel and the pivot as well. Without the double lock, when you push on the table, the pivot will spin – and you can move the table – even when locked. Let’s install the casters next: Below: These are the casters (with double lock mechanism) Below: Use the bottom of the caster to...

Read this entry »


View Lockwatcher's profile

Marshmallow Catapult

04-15-2011 12:43 PM by Lockwatcher | 7 comments »

When I pulled this off of my cabinet, I did not expect so many would like to build these. Well, I took one apart so that we could make some notes – and then detail construction. Below: The marshmallow catapult in it’s finished form. As you can see below, the catapult concists of only 6 wooden parts & some miscellaneous hardware, all easy to build with handtools if need be. When we did this project with the scouts, we put it together as a kit that they could sand &#...

Read this entry »


View mafe's profile

Drill press table and much more! #4: Drill press turning (making a plane knob) Blog

10-07-2010 11:51 AM by mafe | 24 comments »

Drill press turning Making a plane knob on the drill press challenge. Last week I needed a knob for a fence I was making for my no. 3 and 4 planes, and was ready to go to the lathe.- But decided to challenge myself by making it on the drill press, with the simplest means I could find (yes I’m a child).I also took pictures as I went along so I could share it with those who don’t have a lathe. This was how it turned out. A piece of wood, if you don’t happen to have a piece ...

Read this entry »


View StumpyNubs's profile

The Stumpy Nubs Workshop #22: A Drill Press Table that will make your shop weep with joy!

06-09-2012 02:41 PM by StumpyNubs | 32 comments »

Once in a lifetime we achieve a level of perfection so high we wonder if our very lives will ever be the same! That is what I imagine all of you will think the moment you see the new drill press table. Or, at the very least, you’ll have a good time laughing at me. This episode of Blue Collar Woodworking is all about the new drill press table, complete with downdraft dust collection, drawers for storage, and a micro-adjustable, X-Y sliding table. After that we show ou how to ma...

Read this entry »


View scrappy's profile

Making A Segmented Ring Without A Lathe / A Step by Step Tutorial

06-07-2009 09:15 PM by scrappy | 36 comments »

Well, I was asked to put together a blog on how I made my segmentd ring. Since I had to make a new one for myself, (first one too small) I thought I would go ahead and do a step by step picture tutorial. My first time ever doing something like this , so hope it comes out OK. Here goes; Wood Selection The first step in making the ring is deciding what woods to use. As we all know, the selection is quite large. One of the most important things is color, but the most important is hardne...

Read this entry »


1 2 3 4 ... 83 next »
829 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com