LumberJocks

Woodworking blog entries tagged with 'drill press'

  • Advertise with us
View woodchic's profile

starting my kitchen cabinets

08-26-2009 09:29 PM by woodchic | 78 comments »

Hi everybody…....My husband finally got the floor finished…...he did a fantastic job I might add and now…..I finally sucked up enough courage to get started on my kitchen cabinets. The kitchen and dining area is 14 ft wide x 24.6 ft long. My cabinets are made of plywood and my face frames and doors are made out of hickory. I have never worked on a set of kitchen cabinets before, so I am pretty much learning this on my own. I have a friend on here that gives me advice whe...

Read this entry »


View Jim Jakosh's profile

Murphy Bed #1: Building a Murphy Bed from scratch

07-10-2013 10:57 PM by Jim Jakosh | 42 comments »

We need a Murphy bed next winter in Arizona and I did not want to buy the hardware. That takes all the fun out of designing it yourself and costs $360. So I looked at a lot of bed designs and settled on one that used HD pivots, gas springs for counterbalance and a swing out leg support rather than the fold down kind.The parameters were a twin mattress (7×39 x 75), had to flip long ways and enough room inside for making the bed. Then I had to decide on the pivot points, the foot pivot ce...

Read this entry »


View OregonBurls's profile

How to find and harvest legal burls!

10-13-2009 05:44 PM by OregonBurls | 38 comments »

Hey everyone, It was suggested that I start a discussion on how to find and harvest burls. Please give your input also. I don’t deal with straight grain that often. I cut and sell burls for a living so here is what I know. It is illegal to harvest a burl without permission. of course if it is on your own property you can give yourself permission. What I do is put an ad on Craig’s list saying I want your burls. Most people don’t know what burls are. So you don’t get that many calls....

Read this entry »


View scrappy's profile

Making A Segmented Ring Without A Lathe / A Step by Step Tutorial

06-07-2009 09:15 PM by scrappy | 36 comments »

Well, I was asked to put together a blog on how I made my segmentd ring. Since I had to make a new one for myself, (first one too small) I thought I would go ahead and do a step by step picture tutorial. My first time ever doing something like this , so hope it comes out OK. Here goes; Wood Selection The first step in making the ring is deciding what woods to use. As we all know, the selection is quite large. One of the most important things is color, but the most important is hardne...

Read this entry »


View Jerry's profile

Tips and Techiques #2: The Somewhat Invisible Hinge Tutorial

03-05-2015 03:49 AM by Jerry | 33 comments »

Okay, I was asked to post a how to for the, I guess I’ll start calling it “vanishing” hinge, since it’s not completely invisible. Anyway I struggled with posting this tutorial, because in this instance things went badly, but I think it’s just as important to publish the mistakes as the successes, because that way whoever reads this can see where the pitfalls are. So in the spirit of full disclosure, here goes. Okay, this tutorial is for 1/2” wood and dow...

Read this entry »


View Brad's profile

To Shopsmith or Not to Shopsmith

07-28-2008 09:57 PM by Brad | 32 comments »

So I’ve been debating with my father in law about weather or not he should sell his Shopsmith setup invest in building a new shop using standard stand alone tools and machines. He’s about to retire and is kicking the idea around of either selling it or dropping another $1K into upgrading to all new Shopsmith stuff. Personally I’ve never used the SS but I sincerely doubt I’d be a fan. Not being able to move from machine to machine would bug the hell outta me and bein...

Read this entry »


View OregonBurls's profile

Tip of the day! Use a push stick!

01-17-2013 02:59 PM by OregonBurls | 32 comments »

THE ART OF NOT TAKING A TRIP TO THE EMERGENCY ROOM!Yesterday I awoke out of my daze of admiring a quilted maple block with a shocking sensation and blood everywhere. The dull blade on my bandsaw did not help and using my hands to push the beautiful block through didn’t help either. Simple word of advise which many of you can attest too. Keep your tools sharp and use a push stick! Lets say it all together now! Keep your tools sharp and use a push stick!Keep your tools sharp and ...

Read this entry »


View StumpyNubs's profile

The Stumpy Nubs Workshop #22: A Drill Press Table that will make your shop weep with joy!

06-09-2012 02:41 PM by StumpyNubs | 32 comments »

Once in a lifetime we achieve a level of perfection so high we wonder if our very lives will ever be the same! That is what I imagine all of you will think the moment you see the new drill press table. Or, at the very least, you’ll have a good time laughing at me. This episode of Blue Collar Woodworking is all about the new drill press table, complete with downdraft dust collection, drawers for storage, and a micro-adjustable, X-Y sliding table. After that we show ou how to ma...

Read this entry »


View Jerry's profile

Power Tools #1: Shopsmith Mark V Restoration

11-24-2013 02:54 AM by Jerry | 31 comments »

Please don’t laugh, I know all of you out there have “real” power woodworking tools. I could not afford the stuff I wanted as I’m just getting started, and I thought a used Shopsmith might be a good way to get going fast. So I bought this 1954 Shopsmith Mark V on Craigslist for $200.00. After I got it home, it promptly started making all kinds of terrible racket, and I discovered that I had bought $200.00 worth of junk, well almost. I found a place where I cou...

Read this entry »


View Jerry's profile

Home Made Tools and Jigs #1: Self Centering 1/2" Dowel Drilling Jig for the Invisio - Hinge

05-29-2015 08:27 PM by Jerry | 31 comments »

Made from $12.00 worth of bronze bushings and a shaft collar. The shaft collar has a set screw that holds a 1/8” drill bit in place, so you would need to use 1/8” axles for your hinge pieces. The largest bushing has an inside diameter of 1/2”. The second bushing an outside diameter of 1/2” and an inside diameter of 3/8”. The shaft collar has an outside diameter of 3/8”, takes a 1/8” drill bit, and uses an allen set screw that takes a 1/16R...

Read this entry »


1 2 3 4 ... 83 next »
829 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com