LumberJocks

Woodworking blog entries tagged with 'delta'

  • Advertise with us
View RevEric's profile

I'm New: You May Hate Me

12-07-2015 11:02 PM by RevEric | 9 comments »

Hi Everyone. I’ve been trolling this blog for so long that I thought I had an account. I decided to actually get one a few weeks ago. Lately, I’ve been looking to upgrade my table saw. For years I’ve used a Ryobi BT3100. I know everyone has their opinions on what the best table saw is. For me, the Ryobi has been great and met almost all my needs. The fence has been dead on accurate and dust collection excellent. I really like the saw but decided it was time to upgrade. ...

Read this entry »


View Pete_LJ's profile

Delta 46-715 Lathe Repower #3: Part 3 - Fitting Belt and Determining Linear Location of Driven Pulley

06-13-2016 02:36 PM by Pete_LJ | 3 comments »

06132016 It was a busy weekend and I did not get a lot done on this project. But I did make some progress. I was able to fit the motor to the swivel shaft and box while mounted to the lathe. I need to fix the linear position left to right for the hub and driven pulley. I also need to get the tensioner fabricated and adjusted. I have some pics for you with the motor and shaft in rough position and also the driven pulley/hub. The bungee cord (pictured below) is just being used tempora...

Read this entry »


View MikesProjects's profile

New Vintage 20" BandSaw Project, Rust Removal & Biesemeyer Fence Install #1: rust removal on cast iron top & refurbish action multiple videos

06-28-2016 04:03 AM by MikesProjects | 8 comments »

Video links below… Recently I purchased an older 20” bandsaw. I need a larger bandsaw that can handle anything I throw at it.. I think I found that in a mid 70’s Rockwell 20” wood cutting bandsaw. It probably came out of a school wood shop. The motor is 2hp, it has two speeds which can be adjusted with the belt, it has already been upgraded with carter guides, this big boy saw weighs over 600 lbs. I made several videos regarding this saw which i’ll post below. ...

Read this entry »


View withheld's profile

A workshop out of the floodplane #3: A new fence for the old saw

01-19-2011 05:20 PM by withheld | 0 comments »

Based on Jamie's blog entries on upgrading a Craftsman table saw with a new delta T2 fence, I decided to do the same.The fence arrived last night I might need some better drill bits for the job and a good center punch, if I understand his blog entries, but it sounds like the thing to do is proceed very slowly and carefully. Which in my case means measure 10 times, cut once. As an aside the thing the fence is resting on is a small pegboard tool holder I started working on. Given my skill...

Read this entry »


View Sawdustonmyshoulder's profile

Questions about my new Biesemeyer fence #1: Need some advice....

11-11-2016 08:30 PM by Sawdustonmyshoulder | 2 comments »

My new Delta table saw came with a Biesemeyer fence. My old Delta had a unifence. Now, I did like the unifence and found it to be rock solid and versatile. I particularity like the flip stop on the bottom of the rail. Man, I used the stew out of that feature. Now, today….the Biesemeyer fence doesn’t have this feature. I am hoping my LJ buddies out in Workworkland can give me a hand. (poet and don’t know it) What do you all use to ‘remember’ settings on your &#...

Read this entry »


View Dekker's profile

Reviews - Tools #1: Delta Shopmaster Bandsaw - SM400 - A Budget Bandsaw

10-21-2007 12:49 PM by Dekker | 2 comments »

So I finally made an excuse to buy a new tool – a bandsaw to be precise. The problem is that I can not foresee a need for a heavy-duty model, nor can I justify its expense at this time. For that money, I could simply ask my wood supplier to resaw it for me for a few bucks. I went to my local BORG and could only find mid-priced models, $400-800. This was more than I was willing to spend. Then I went to Canadian Tire, since there is currently a 1/3 off sale (thanks MsDebbieP for pointi...

Read this entry »


View Kevin's profile

Delta Unisaw #1: Cleaned up and trying to decide if I should keep it.

01-27-2008 07:27 AM by Kevin | 15 comments »

I have decided to put all of this into a blog instead of the forums. Here is a link to the previous forums. Should I buy this Unisaw? http://lumberjocks.com/topics/1877 Unisaw Advice Needed? http://lumberjocks.com/topics/1989 Well, I finally got pictures of it. I wish I had pictures from before working on it. I have spent a lot of time trying to clean up the cast iron top. I tried to get pictures that show what it looks like, but it is hard to capture. I picked up a new tape for the ...

Read this entry »


View The__Dude's profile

Learning my tools #1: Storage Shelves

08-31-2015 04:33 AM by The__Dude | 0 comments »

Decided to work with my new tools for a simple project.Storage shelves to organize my future wood area. I decided to use my new table saw and ripped rhe pine square.Never used a dado blade, so I cut the front pibe to hide the plywood edge. I used my Kreg jig to pocket hole to keep the front pine clean.

Read this entry »


View woodchips's profile

New (used) Delta Table Saw #2: Here it is...now gotta clean it up.

10-08-2008 05:57 PM by woodchips | 7 comments »

Well I was finally able to go pick the saw up and I’m every bit as excited as I was when I first bought it. I’m going to be doing a bit of work on it before using it. I need to rebuild the right wing extension and I’m going to build a router table into it. I also need to give it a good cleaning inside and lube it with some sort of dry lube (any suggestions?). The cast iron surface has some very minor rust spots that will need to be removed, what would be the best way t...

Read this entry »


View GlennsGrandson's profile

From Rust to Lust, can I bring it back? #6: Tedious Tape-up... and jigs? Bed/Fence protection??

04-25-2012 08:05 PM by GlennsGrandson | 4 comments »

Hello again, I’ve got quite a bit accomplished since my last post, but it took much longer than anticipated. I had to finish cleaning a few little pieces here and there and wipe off the never ending paint dust with mineral spirits. Once I’d clean a piece I’d tape it off, lots of masking tape and razor blades. The only pieces I have left are the pieces of the head. I have to clean up the head yet and probably replace the bearings, they felt good and sounded good but they prob...

Read this entry »


« prev 1 ... 4 5 6 7 8 next »
72 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com