LumberJocks

Woodworking blog entries tagged with 'canary wood'

  • Advertise with us
View GeneR's profile

Education and torment #1: Canary wood Box

12-15-2013 06:36 PM by GeneR | 2 comments »

The box is 4” square and made from canary wood and walnut, with a birdseye maple and walnut top. This started as an idea for the wifes Christmas present and grew to a little monster. I first decided on the box size being determined buy the length and thickness of the piece of canary wood. the piece was about 28 in long 4 1/2” wide and 1/2” thick so 4” square gave me some screw up room. At this time I figured I would use a 1/4” piece of plywood for the bo...

Read this entry »


View Don's profile

Double Dovetail Box #6: The End

02-07-2010 09:05 AM by Don | 5 comments »

The box is almost done. First thing I did today was cut the top to fit. I inititially cut it the same size as the box but decided to cut it a bit smaller so that the corners would show through which I thought gave it a nicer look. I also rabbited the under side of the top a bit to hold it in place. I generallly like lift off lids better than hinged lids for a couple of reasons: I think the metal of a hinge can distract from the beauty of the wood, and I’m too lazy to go buy the hinges. ...

Read this entry »


View Don's profile

Double Dovetail Box #5: Assembling the box and Starting the top

02-01-2010 07:52 AM by Don | 4 comments »

Everything about the double dovetail joint is complete. I hope it was cear enough for folks to make their own. Feel free to bug me with questions if you didn’t follow. In summary, it’s just a bunch of half blind joints using a corner piece with the grain perpendicular to the sides. From here on out it’s just another box but I’ll continue to post shots as I go. Yesterday I lightly sanded the shellac that I previously applied to the inside surfaces of all pieces. Then...

Read this entry »


View Don's profile

Double Dovetail Box #4: Cutting The Remaining Dovetails

01-26-2010 03:23 PM by Don | 4 comments »

I didn’t quite get the box assembled on Sunday but I was close. Next step after gluing the corners is to cut the remaining half blind dovetail joints. I thought I was going to have to do a second setup on my jig to cut these like I had to on my Spalted Mango Box but I didn’t. On this box I’m reversing the joints end for end rather than doing a mirror image. Half blind dovetails are actually always reversed end for end like this when cut on an Omnijig and probobly on most ...

Read this entry »


View Don's profile

Double Dovetail Box #2: Cutting the first set of dovetails

01-11-2010 07:26 AM by Don | 2 comments »

I’m not planning on going into all the gory details about how to cut the dovetails, that would be a lengthy blog by itself and it’s highly dependant on your choice of jigs or hand tools. I use a Porter Cable Omnijig but I’m sure any jig capable of making a half blind dovetail will suffice. If there’s enough requests then I may do another blog on that or could go into more detail on this one. Step 1: Clean up the glue from the boards that you glued the corner pieces ...

Read this entry »


View Don's profile

Double Dovetail Box #1: Milling the parts.

01-10-2010 08:42 AM by Don | 7 comments »

A1Jim suggested I post a blog to describe how I did the double dovetail Joint I used on my Spalted Mango Box so here it goes. I hope people find this helpful and if you have questions please post them and I’ll do my best to answer them. I also greatly appreciate feedback on anything. I was going to show how to make the joint using some scrap wood but since it’s just as much work as using good wood so I decided I may as well use good wood and build a whole box. I’ll be pre...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com