LumberJocks

Woodworking blog entries tagged with 'bench crafted'

  • Advertise with us
View siggykc's profile

Mini-Roubo from Oz #3: My first workbench build: Leg Vise - The beginnings

07-28-2019 10:31 PM by siggykc | 0 comments »

Gday all! So, whilst I was constructing the base of the bench, in parallel i had been keeping an eye out for folks selling interesting timber that I could incorporate into the bench.As i live in essentially a flat sized house, I dont have a huge stockpile of timber and just acquire it as I go.I came across a bloke who had an old hard maple bowling alley that he had ripped up. After close inspection, i figured it wasn’t the ideal thing to incorporate into the bench, but he had a shipp...

Read this entry »


View wrenchhead's profile

Moxon Vise Build

09-28-2018 12:31 AM by wrenchhead | 3 comments »

I made this Moxon vise to bring my work up to a comfortable height when laying out and cutting dovetails and other joinery. The vise is 24 inches between the screws so I can clamp wide boards. The vise has really good clamping pressure and like all the Benchcrafted hardware I have seen, everything operates smooth and fast. Thanks for watching! https://www.youtube.com/watch?v=7vBXvlP4bEs

Read this entry »


View ic3ss's profile

Split Top Roubo Bench Build #19: Done!

04-14-2015 02:15 AM by ic3ss | 4 comments »

My morning was taken up entirely by straightening out a snafu with my medical insurance co. and the doctor’s office. What a pain. Sometimes I wonder why I have health insurance. Anyway. . . When I did make it out to the shop, I had this cutoff piece of walnut left over from the leg vise chop that was perfect for the deadman. I’m not really done with it at this point, all I did was rip it and cut to length, cut a rabbet at the top and the V groove at the bottom. It fits right...

Read this entry »


View ic3ss's profile

Split Top Roubo Bench Build #18: Top flattening, parts 1 and 2

04-13-2015 03:49 AM by ic3ss | 0 comments »

I didn’t write the final post last week as I was pretty busy with my 20th wedding anniversary. Last weekend I had planned on flattening the tops on my last day off but only got half of it done. I had decided to use the router to flatten it, using a sled and rails. I saw the technique on the Wood Whisperer video and thought it was a good idea. So I went to the big box and got two 2×6 kiln dried 8’ long boards for the rails. The first thing it to make the edges straight and ...

Read this entry »


View ic3ss's profile

Split Top Roubo Bench Build #17: Ok, I think I've recovered now

04-07-2015 12:07 AM by ic3ss | 3 comments »

After a long morning drinking my coffee and thinking about alternatives to keep working, I drove to the lumber yard and got a piece of baltic birch to make the flattening sled out of. When I came back I took my bent saw blade out and put a crescent wrench on the bent tooth. I moved it about three times and I think it may be useable. I soaked it in simple green to get the pitch off and I’ll try it tomorrow. I’m expecting that it’ll be a little rough but that’s ok. IR...

Read this entry »


View ic3ss's profile

Split Top Roubo Bench Build #16: The worst Easter ever

04-06-2015 01:46 AM by ic3ss | 4 comments »

So, my task today was to cut up a piece of maple I bought the other day to make the gap stop and get it glued up in the clamps and then go over to family for Easter dinner. I set up the band saw and set about resawing the board into two halves. It went fine for the first 3/4 of the board then it was binding the blade and was not tracking straight, and not wanting to cut. I made a couple of adjustments, everything else looked fine in the setup. It just wouldn’t cut and was binding hor...

Read this entry »


View ic3ss's profile

Split Top Roubo Bench Build #15: Pretty much done

04-01-2015 11:02 PM by ic3ss | 13 comments »

I put in an eleven hour day yesterday on this thing, the work was really kind of fun compared to the tedious work of digging out mortises of the day before. I’ve never tried the draw bore method of locking a mortise and tenon together. I didn’t even use clamps. Well this morning I just had to get the tops to fit on the tenons, so after trimming back a couple of mortise surfaces they both fit down snugly, a very sweet fit. As a bonus, the sides of the tops ended up flush wit...

Read this entry »


View ic3ss's profile

Split Top Roubo Bench Build #13: Cut tenons, make mortise jigs

03-30-2015 12:38 AM by ic3ss | 0 comments »

Whew, my workweek is finally over and now I can have some fun. I’ve been thinking all week about today, particularly what I still need to get to push this project along. I needed a jig to cut the mortises, and I was looking at pattern bits and I came away with an education. Top bearing straight cut pattern bits are expensive. I didn’t want to spend that much so I went to woodcraft last week when I bought my last pieces of wood for the leg and rail, and picked up a guide bushing fr...

Read this entry »


View ic3ss's profile

Split Top Roubo Bench Build #12: Finish up the leg vise

03-25-2015 02:37 AM by ic3ss | 1 comment »

Had a surprise today, more funds available in the budget than I thought so I went to the lumber yard and got the wood that I needed. Got it all milled up and the front rail is now in the clamps. Due to my clamp shortage, I’ll have to glue up the last leg after I get home from work tomorrow night. But that’s good because it’ll set me up perfect for next weekend’s activities. I picked up a 2 – 5/8” forstner bit for the plastic bearing ring, a 4” fors...

Read this entry »


View ic3ss's profile

Split Top Roubo Bench Build #11: A chop is born

03-23-2015 11:21 PM by ic3ss | 0 comments »

Today was a light day for me as I’m running out of things I can do until I get more wood, so today I cut out the side profile of the chop. I had this piece of thin ply laying around so I ripped it down to size and put my alignment marks on it, then drew the shoulder using a french curve template. Using the centerline I was able to do both sides. I clamped it on edge and sanded the template profile smooth then traced both sides on the chop. I cut a bunch ...

Read this entry »


1 2 next »
14 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com