LumberJocks

Woodworking blog entries tagged with 'bar clamp'

  • Advertise with us
View Dave Rutan's profile

Building Dave's Bar Clamp #7: Finishing up

09-28-2016 12:26 PM by Dave Rutan | 0 comments »

[Legebla ankaĆ­ en Esperanto] [Above] After the movable stop is on the bar, insert a piece of 1/4 in. dowel into the hole at the end of the bar. This keeps the head from sliding off. The dowel can be glued in, but if it is snug, you may want to leave it be. If left removable, the possibility is open to join two clamps together to make a longer one. [Above] Take the 1 in. x1 in. x 4 in. piece of wood and drill a 3/8 in. hole down the center about 3 in. deep. Using epoxy...

Read this entry »


View Dave Rutan's profile

Building Dave's Bar Clamp #6: Movable stop

09-28-2016 12:14 PM by Dave Rutan | 0 comments »

[Legebla en Esperanto] [Above] Cut the piece of flat steel into two lengths of 3.25 in. Use a file to blunt the edges and round the corners a bit. [Above] mark a point about 3/8 in. in from each end, centering it on the steel. Drill a 1/4 in. hole at these locations. You will want to use a center punch to give the drill bit a place to catch. The hole is easier to drill if you start with an 1/8 in. pilot hole, then go to the 1/4 in. bit. File any burs. [Above]...

Read this entry »


View Dave Rutan's profile

Building Dave's Bar Clamp #5: Finishing the jaw

09-28-2016 11:01 AM by Dave Rutan | 4 comments »

[Legebla en Esperanto] [Above] And here’s me forgetting to photograph steps, but it’s OK. Advance the threaded rod a few inches. Put the jaw half with the through-hole on the bar and with the rod through it. Put a washer on the rod and into the well you drilled. Glue the nut on the end of the threaded rod. Now you should have what is shwn in the top photo. 2nd photo: put the other washer in the well of he other jaw half. Apply wood glue to the inner surface of ...

Read this entry »


View Dave Rutan's profile

Building Dave's Bar Clamp #4: The Bar

09-28-2016 10:59 AM by Dave Rutan | 0 comments »

[Legebla en Esperanto] [Above] Now turn the bar over to expose the bottom side. Put both jaw pieces on the bar up against the head. Measure in 2 inch increments from the jaw pieces down the length of the bar. In reality one in increments is better, but it’s double the work too. Using the rat tail rasp cut half circle stops into the bar. N.B. More can be easily added after the clamp is finished. Don’t go all the way to the far end. [Above] Round ove...

Read this entry »


View Dave Rutan's profile

Building Dave's Bar Clamp #3: The Jaw

09-28-2016 10:57 AM by Dave Rutan | 0 comments »

[Legebla en Esperanto] [Above] Now take one of the 3 inch pieces and put it on the bar in front of the clamp head that you recently glued onto the bar. Mark the height of one of the side members of the head on the 3 inch piece. N.B. in this position the area above the head is going to be the fingers. [Above] Using the other 3 inch piece, place it in the ‘finger’ area of the one you just marked. Center it from side to side and mark where it sits. [Abov...

Read this entry »


View Dave Rutan's profile

Building Dave's Bar Clamp #2: The fixed head

09-28-2016 10:54 AM by Dave Rutan | 2 comments »

[Legebla en Esperanto] [Above] Take the 2 inch piece and measure 1 inch from one end. That end is henceforth the bottom. Mark the center between the sides and put a dimple in that spot. I used a convenient nail here. [Above] Now, using a 5/8 in. bit (or better, one just big enough for the nut,) drill a hole just deep enough for the 3/8 in. nut. You can see my hole is a little large. [Above] In the center of the shallow hole you just drilled, now drill a 3/...

Read this entry »


View Dave Rutan's profile

Building Dave's Bar Clamp #1: Supplies and cutting

09-28-2016 10:19 AM by Dave Rutan | 2 comments »

[Legebla en Esperanto] I recently built two more of my wooden bar clamps. I decided to take photos along the way to show how they are made. These are made of 1×2 pine. Most of my bar clamps are of a very similar design. I’ve used them. They haven’t broken and they hold wood together during glue-ups. Using a stronger wood would make the clamp… well, stronger. N.B. I made these with basic hand tools. Using better tools will yield a more professional looking proje...

Read this entry »


View Igor's profile

Tools for woodworking #1: Shopmade Metal Bar Clamps

03-16-2016 05:15 PM by Igor | 2 comments »

Shopmade Metal Double Bar Clamps video:https://youtu.be/0mKuJ7O4t7Q

Read this entry »


View Marty Backe's profile

Upgrade your Harbor Freight bar clamps with these easy enhancements

09-21-2015 01:36 AM by Marty Backe | 7 comments »

I was never a fan of the cheap aluminum bar clamp. They would twist like a pretzel when any decent amount of clamping pressure was applied. Then I read what Paul Sellers had to say about these clamps, where he offered an easy upgrade path that turned them into decent medium duty clamps. You don’t always need the strength of a Bessey type clamp. In this video I demonstrate how I perform the ‘surgery’. I recently bought two more Harbor Freight 48” aluminum bar clam...

Read this entry »


View Siegel_KenEvil's profile

Toy Table Side Notes

01-02-2014 01:15 AM by Siegel_KenEvil | 0 comments »

I needed better lighting for my varnish application for the “Toy Table” build. The clamp on my old halogen lamp didn’t work very well in many situations. By drilling a hole at the end if a bar clamp, I was able to replace the original clamp with a bar clamp. It worked great. You may notice my Christmas tree in the background of some of the pictures from the “Toy Table” build. It’s decorated with ten 1.5” plasma balls. These are 12V devices int...

Read this entry »


1 2 next »
12 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com