LumberJocks

Woodworking blog entries tagged with 'ash'

  • Advertise with us
View WoodJediNTraining's profile

Make a Cross Cut Sled For Your Tablesaw

04-26-2013 05:44 AM by WoodJediNTraining | 11 comments »

The one Project Video I get asked the most to make is how to build a crosscut sled for the Tablesaw. Well there are a lot of videos out there on making a Cross cut sled, so this is my take on it. I hope you can take something from this video and use it in your shop

Read this entry »


View kaerlighedsbamsen's profile

Loudspeaker Dieter Rams tribute Blog

02-04-2014 10:50 PM by kaerlighedsbamsen | 12 comments »

This is a blog on how i made this project: http://lumberjocks.com/projects/96630 These days my shop is cold. Really cold. It is open on one side and it has been about -5 degrees C outside for a while now. I can only be out there for shorter durations of time and wearing thick layers of clothing. But it has been quite a while since i made my last project and i really had a need to get in my shop and tinker a bit. What to make that is not too big a project and that improves beeing ins...

Read this entry »


View WoodJediNTraining's profile

Build a Finger Joint Jig

05-23-2013 04:35 PM by WoodJediNTraining | 15 comments »

Recently I posted a video covering common woodworking joinery ( http://www.youtube.com/watch?v=zqXLYe783qw ) with the help of a few friends. In that video I talked to you all about making finger joints on the table saw and showed you a finger joint jig in the process. Well as I promised, here is the complete build process of that Jig. Table Saw Finger Joint Jig Also a little reminder about the 2nd Annual Whirligig Wars. It is almost here!! The event Runs from July 10 –...

Read this entry »


View douglbe's profile

Guitar Stand

10-15-2007 04:12 PM by douglbe | 3 comments »

This isn’t much of a blog, but here are some drawings (for those who were interested) with the dimensions for the guitar stand I posted a few weeks ago.

Read this entry »


View pjones46's profile

Preventing Blotching Using A Wash Coat #1: Finishing with Wash Coats

01-04-2015 03:10 AM by pjones46 | 2 comments »

Wash Coat #1: Finishing with Wash Coats I am starting to put together an article covering finishing and this will be part of the coverage but not just limited to preventing blotching as a wash coat will aid in a more consistent staining color. This will be updated as my thoughts are organized. This is only a small portion: A wash coat is a coat of thinned finish that’s applied to bare wood to partially seal the surface before a stain is applied. It reduces the amount of stain from so...

Read this entry »


View degoose's profile

David's [aka Patron] double curve..my version of the jig? #1: Where to start? The Table!

06-10-2009 10:07 AM by degoose | 19 comments »

I have spent the last few days in the workshop working out how to make this jig.. and have it durable and repeatable and totally accurate and easy to use.Actually this jig can be used for two different projects … well probably more that two but thats all I have used it for so far.To start, I had to build a table to go over the bandsaw table for the jig to pivot on. [double pivot actually][two pivots two pics right!! ]The table was made from 5/8” [15mm] plywood, with silver ash us...

Read this entry »


View farmerdude's profile

Cedar Strip Canoe Build #1: The Wood

12-12-2015 11:25 PM by farmerdude | 14 comments »

I am building a canoe for my sister’s boyfriend. He wants a sixteen footer. I am going with the Wabnaki model from Gil Gilpatrick’s book. I’ve never done a blog before and am not real good with computers, but I will do my best. I’m going to start off with just a few things and if I see there is interest in this blog I will continue until it is done. So if anyone out there is interested just post and let me know and I will continue. So, first pic. is the white cedar I b...

Read this entry »


View WoodJediNTraining's profile

Building a Tablesaw Base Part 1

04-11-2013 12:15 AM by WoodJediNTraining | 13 comments »

Recently I had a need to build a new table saw base for my saw. Rather than just building a simple replacement base, I opted to build one with lots of storage potential. This new base measures 6 feet long by 2 feet wide, which gave me good reason to move over to the new shop building. I haven’t yet finished the new shop set up ( haven’t even started) but this build is a great start giving me lots of options for storage potential… This build is a 2 part project. So be sure to...

Read this entry »


View grosa's profile

Making of a cinderella carriage bed #1: Wagon wheels

02-03-2013 02:24 PM by grosa | 16 comments »

This is what the completed bed will look like. These are the spokes for the 48” back wheels. This is the rim for the front wheels. These are the front wheels. Front and back wheels. The radius at the bottom of the spokes was cut on the table saw by locking down the miter gauge and pushing the wood into the blade from the side and it was done in 4 passes. We used an 8” dado blade. This is the back of the wheel where the axle will go into Ne...

Read this entry »


View WoodJediNTraining's profile

Woodworking 101 - Common Woodworking Joinery

05-19-2013 06:34 PM by WoodJediNTraining | 5 comments »

I ask a couple of my woodworking friends to help me talk to you about some common woodworking joinery. Woodworking joinery is the method of joining two pieces of wood together to create a more complex item. Woodworking Joinery is the one thing we as woodworkers need to know and this video talks about 4 common woodworking joints that you are most likely to use in your projects. In this video you will learn about the following joints Half Lap Joints – Presented by Jay Bates Jays...

Read this entry »


« prev 1 2 3 4 5 ... 74 next »
737 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com