LumberJocks

Omar157's Forum Topics

  • Advertise with us
View Omar157's:homeworkshopprojects (0)blog (0)reviews (0)forum topics (12)buddies (0)favorites (0)activity logWatch
05-07-2017 05:12 PM

Help finish will not dry - 10 replies

Hey guysI built a stand for a few benchtop tools using a solid birch door and some Doug fir lumber that were left over on a project. Both of these woods are prone to blotch and I ran out of pre conditioner. I read that I can thin down bullseye shellac with denatured alcohol down to a1lb cut and use that as a sealer to control blotchiness. I mixe...

11-28-2016 05:52 PM

My harbor freight workbench furniture grade upgrade. Almost too nice - 11 replies

I had to fix one handle due to rushing from the excitement of finishing but it’s all fixed up. The bench finally has heft to it and doesn’t wobble all over the place when using the vise. Total spent was about $175 but only because I have loads of walnut. Top is basically the same other than I lined the bottom with 3/4” walnut t...

06-13-2016 08:25 PM

Is bigger really better - 22 replies

Hey guysLast year I really got into woodworking after stumbling on to a video while bedridden from an terrible injury. From that day I spent the next 8 months in bed and watching video after video. Once I was fully healed I started purchasing the tools I didn’t have and pnow have a fully loaded operational shop in my garage. I have everyth...

05-04-2016 01:19 AM

Brett-guard - 1 reply

Hey guys now that I have my unisaw finally running I really need to control the dust up top and I really like my fingers. Did HTC stop making the Brett-Guard? I have been searching online and on their site and I cannot find it. If they did what are most of you using? I really like the shark guard but 8 weeks is a long time to wait for one. Any h...

05-02-2016 12:29 AM

Incra ts-ls fence - 11 replies

Hey guysI just purchased and installed the Incra ts-ls saw fence and I have a small issue. After squaring it up to the miter slot I used my woodpecker set up dial and it seems like I’m off 5 thousandths in the center. I am getting the same reading on both ends but as I move along the face I get the 5 thousandths difference. It starts abou...

03-28-2016 03:30 PM

Delta unisaw rebuild hit snafoo - 35 replies

Hello gentsI have been rebuilding an 87 unisaw for the last couple of weeks and am down to the wire. I went to square off my blade and I just cannot the blade 90 degrees. I spin the wheel as far as it goes until it bottoms out and it seems if I could just spin it a 1/4 turn more the blade would be in position. The blade is dead flat and I pulled...

03-14-2016 02:15 PM

Hvlp harbor freight cup liners - 23 replies

I feel like a complete dummy for asking but I purchased the cup liners and was wondering if I’m supposed to cut a hole in the liner or cut the whole bottom out or what to do. Also does anyone know what the hardest clearcoat finish is? I am restoring a delta unisaw and want to make it scratch resistant. Thanks guys.

03-13-2016 10:41 PM

Looking to trade my Tonneau Cover for shop tools Ford F150 New Jersey - 0 replies

I am a new woodworker and have quite a bit of tools already but you know you never have it all. I am missing a bandsaw, drill press, jointer,CLAMPS and misc tools. Let me know what you have you never know. we can work it out as an even trade or cover and cash depending on what it is and condition. I have three tonneau covers for a Ford F150 5ft ...

03-11-2016 11:47 PM

Outfeed table saw removal - 9 replies

Hey guysI started rebuilding my delta unisaw and have finally made it to the outfeed table. I completely sanded it and should be ready for paint tomorrow but I have clue on how to remove the rollers. I’m sure I can paint it while they are on but it would make a world of difference if they were off. I would have mounted one side in and the ...

02-23-2016 06:41 PM

How much is black walnut worth? - 9 replies

I picked up a bunch of scraps and full length pieces of black walnut on Sunday and was curious to what it would have cost me if I paid full price. I got roughy 20/6’ of 1×6, loads of short lengths from 12’-48”. Plywood cuts and loads of trim all for $150. I estimate it at 700 lf. I usually donate my time and make furniture...

02-23-2016 06:22 PM

Old lumber - 8 replies

Can someone tell me what kind of wood the old 2×4 were?How do they look if I run it through the planer and finish them?Thanks

02-17-2016 02:25 PM

Delta Unisaw I found on CL - 15 replies

I purchased a 34-801 unisaw today from 1987 for $300 it included a custom locking dolly with a diamond plate which the saw is bolted to and a steel outfeed table with rollers in great shape. It needs about an hour worth of work to get the top clean but other than that the top is dead flat and the motor was super super quiet. You can tell it̵...


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com