LumberJocks

Jeff82780's Forum Topics

  • Advertise with us
View Jeff82780's:homeworkshopprojects (13)blog (0)reviews (0)forum topics (41)buddies (2)favorites (275)activity logWatch
12-19-2015 05:57 PM

Which bandsaw would you buy? - 21 replies

So after countless hours at attempting to resaw on my ridgid, I gave up. I still have a lot more resawing to do. Therefore I’m ready for a new bandsaw. I was ready to buy the grizzly 17” aniversary saw, but when I started to read reviews. It sounded like the extreme series was a better option due to cast iron wheels. I’m not ne...

12-04-2015 03:07 AM

Bandsaw help - 13 replies

Trying to resaw some 8/4 red oak for a bow arm morris chair and am I failing miserably. The problem I am having is the top is about a 1/16th if an inch off from the bottom. I set my drift angle. Bought a new wood slicer blade. Then I checked the blade for square. Left side of blade square. Then I checked the right side of the blade and it wasn&#...

09-23-2015 10:42 PM

Shapton pro waterstone advice - 2 replies

What’s up fellow LJ’s! I need some advice. So today my new lie nielsen honing guide arrived.haven’t used it yet, but I’m off tomorrow and gonna get a sharpening session in. Anyway, since I have this new guide I’m itching fot new stones too. I already have the norton 1,000, 4000, and 8000 grit. I like these stones bu...

03-05-2015 11:43 AM

another dovetail question - 3 replies

Hey guys, I am making a small wall hanging cabinet which includes a drawer at the bottom. The drawer is dovetailed front and back along. The back is smaller than the front for the bottom to slide in, and it is also 1/4” down from the top to prevent the top from scraping. Anyway my question is, how do I lay out my pins and tails for this ba...

07-15-2014 09:41 PM

coffee table wood species - 8 replies

In the process of building a fine woodworking coffee table. Frame is out of mahogony. Problem is i ran out. I have some hardd maple i could use for th shelf and top. You guys think that would look alright. Or should i go buy more mahohony?

07-13-2014 12:32 AM

tablesaw blade not raising. please help - 14 replies

I have a grizzly go715p hybrid saw. So i am clueless what is going on. Really frustrated. The handle wont even turn. At first i thought it was jammed with a piece of wood or dust. So i opened the cabinet and noticed a washer and a horseshoe like washer in the bottom of the cabinet. I blew all the dust and debris off and still no luck. I then re...

12-18-2013 01:10 PM

i screwed up - 4 replies

so i am building a new router table and and currently working on a melamine top. anyhow while i was routing the opening for the router plate, my template moved off coursr. now there is a gap about an 1/8” big on the right rear side . so frusttating! anybidy havr any ideas on a quick fix to fill in the gap? i know its not a piece of futnit...

06-14-2013 04:14 PM

scrapershave - 1 reply

I’m making a scraper shave and am having a difficult time with this thing. how much should the blade protrude?

06-01-2013 09:44 PM

a call to experienced dovetailers - 1 reply

hi, am am going nutz over here! I keep getting gaps in my shoulders or baseline. I’ve tried different techniques such and nothing seems to work. Is there something I could be doing wrong that I am not aware of? thanks.

11-25-2012 02:24 PM

shooting board help - 9 replies

so i just made my first shooting board and i love it. I wish i would’ve built one sooner. But anyway, I am having one problem. 1. I shoot one side of long grain. 2. register that side on fence and shoot the end grani.3. i repeat and do the same sreps for the other side. the board comes out square except for end grain i shot in the first s...

08-12-2012 11:01 PM

smoothing plane leaving scalloped surface - 23 replies

I just bought a woodriver no.4 yesterday and i love it. I sharpened the blade and put a slight camber on it. However, when preparing the board for finish, I am gettting a scalloped surface instead of a smooth one. It’s not noticeable to the eye, but you can feel them when you run your hand across the board. I baerely have the blade retrac...

05-14-2012 09:46 PM

bought me a new jointer - 3 replies

well i finally splurged and bought a shop fox w1741 8” parallelogram jointer. So my question is how accurate do you guys usually get when it comes to getting both your tables to parallel. I can fit a .002 feeler underneath , but not a .003. is this good enough or should i aim for better? what ya think.

12-26-2011 05:17 AM

another jointer problem - 13 replies

hello everyone and merry christmas. well as some of you know i am building my first woodworking bench. I was having a real difficult time jointing long 8’ boards for the top. I thought the problem was that i wasn’t keeping the board supported. So i decided to build some infeed and outfeed extensions for my jointer. so i cut some 2...

12-19-2011 01:44 AM

jointing long boards - 14 replies

im building a workbench for my shop and need to joint some 8’ 2×6’s for the top. for some reason i am having a helluva time doing this. i must have ran 1 board through about 10-15 time to get bthe face flat. I am noticing that the first half of my board is jointing good, but the last 3’ft or so is not jointing. i dont know...

12-02-2011 06:50 AM

aligning my grizzly go715p hybrid TS - 6 replies

Decided to try to tune up my grizzly go715p hybrid tablesaw. First let me tell you that i am having a helluva time aligning this saw precisely. I did find that there is no run out on the flange. so i then moved on to aligning my miter slot to the blade. its off by .004. i am not sure if i am in good standards so i figured i would try to get it a...

11-14-2011 03:42 AM

tablesaw squeaking - 13 replies

Today i decided to tuneup and cleanup my grizzly go715p tablesaw. I did this mainly because i’ve had the saw for about a year now and have not done any maintenance to it yet. Plus i just bought a woodworker II 48 tooth full kerf blade so now was the perfect time. everything went good, adjusted fence parallel to blade and made sure blade wa...

11-01-2011 06:42 AM

mortiser problem - 9 replies

just purchased my first benchtop mortiser and i love it. well….....except for the fact that everytime I use it the auger bit slips from the chuck. Has anybody else had this problem? any suggestions?

10-21-2011 02:56 AM

help with rust - 6 replies

left the garage open accidently on a day when it was raining. My new jointer had rust spots all over it. i did manage to remove them , but there is some stains from the rust that i cannot seem to remove. ive tried 800 grit wet sandpaper with wd40, but no luck. anyone have any idea how these stains will go away? thanks -Jeff

08-25-2011 04:35 AM

another plane question part deux - 9 replies

WELL the good news is that my sharpening skells i think are becoming a little better and and finally cambered the plane iron on my #4 smoother. My question is that why is it that when the blade is barely protruding (but is protruding) the blade is not grabbing any of the board. this is only when i am planing the face of a board. when i turn the ...

08-24-2011 12:50 AM

another handplane question - 12 replies

well thanks to everyone here, i think im finally starting to get a hang of it. well maybe just a little bit. However my question is that everytime i’m planing the face of a board either with my #$ or block plane i get these horrible lapping maks in the wood. what is causing this?

1 2 3 next »
41 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com