LumberJocks

DangerDoug's Forum Topics

  • Advertise with us
View DangerDoug's:homeworkshopprojects (0)blog (0)reviews (0)forum topics (14)buddies (0)favorites (1)activity logWatch
08-19-2021 09:32 AM

Biesemeyer Guide Rails -- Source? - 14 replies

Hello all, This question is age old but need help finding a replacement front rail: 2” x 3” x 3/32” [0.0938].Bought the Unisaw (34-771) back in the early 80s and it is still in great shape. I did purchase/install a Biesemeyer system some time ago, but only a 64” long front rail. My buddy sent me the woodman video, but ...

07-18-2021 10:39 AM

Help With Miter Cuts - 46 replies

Good morning all, I was having trouble getting a good miter cut on a simple project.The tools I was using:Bosch 12” slider with $50 (sale price) Makita crosscut blade Heavy Rockwell 10” T-Saw – also a $50 blade[this Rockwell had a major tune-up last year, all new bearings, etc.]This is not about cutting square or chipping, t...

01-15-2019 10:25 AM

Help with UNISAW 34-771 - 21 replies

Please excuse any redundancy on this question, but my UNISAW is ready for a tune up.I cannot stop the back-of-the-blade from hitting the rip and leaving behind the dreaded saw marks. Tried moving the top several times, with and without a dial caliper, tried many blades; on and on. It also vibrates and squeals.So in all three issues: Cannot ce...

06-21-2018 08:06 AM

Powermatic 511 help please - 2 replies

I have been looking at Panelsaws for a while and found a slightly used Powermatic 511 in near perfect conditon. Brought it to the shop and after spending a couple of hours going over it top to bottom I was thinking this looks more like a floor-model than a used saw.That said the carriage appeared to have a lot of play, so tweaked a few of the UB...

08-12-2017 09:12 AM

Duo Fast MS 7664 never had much luck - 2 replies

I have two old Duo-fast air nailers, they worked fine for a job or two but found they don’t do well when not used.E.g. my MS 7664c stapler (gold/hammed paint color) is in new condition and only was used it for a few small jobs. The issue now, when connected to air, air escapes out of the head.I assume, it sat too long and the O rings fl...

07-13-2017 09:57 AM

Help Rockwell Unisaw 3 hp Single Phase Hookup - 12 replies

Help I moved and need to rewire the shop.The question is what is the minimum size wire and/or breaker I need for a 32 year old 3hp – single phase Rockwell Unisaw (I bought new).Can I get by with 20amp and 12 gauge wire 225v hook up. The run from the panel is about 50’. I noticed this house (built 2002) doesn’t seem to have t...

07-20-2014 12:33 PM

Router - Brass Locking Ring Nut Needed - 6 replies

Any ideas where to find a 1-1/2” brass ring nut to fit these guides?[PC guides are smaller]OakPark is out of stock and don’t have a single one. http://us.oak-park.com/catalogue.html?list=BG-- OR open for suggestion what might fit – bike part – etc.Of course if somebody has an extra will purchase (0; Thanks!

06-24-2014 08:28 PM

DIY Edge Lipping Planer - 3 replies

Any folks build a DIY edge lipping planer?Need to plane-down 3/4” x 7/8”+ poplar off a 3/4” plywood edge. Found the Hoffman which is very nice, although a bit pricey. Seems like this is a common task and there must be some DIY lipping tables or jigs that can be made with a mid-size router.Any pics out there that can be po...

03-24-2014 09:05 AM

Mikta 2401B Miter Saw - Fix - 8 replies

Have an old Mikta 2401B, it’s in great shape but has had a problem for a long time.It will grab pieces and throw them around the room, I got used to that but thinking may be a good time to fix. Any ideas? Could the fence be bent? it’s cast iron, so that’s hard to believe.Blade wobble? I can’t really see any, can se...

01-27-2014 10:19 AM

Inserting router in table saw leaf - 11 replies

Need to consolidate some of the equipment at the shop – what is a good way in insert a heavy router, motor down in a table saw leaf? Guessing they sell plastic ones, but what about a 12” x 12” x 1/4” Alum. plate? Is the common method just drill appropriate holes in plate and router the 12” x 12” plate back ...

01-26-2014 08:17 PM

DEWALT 746 Table Saw need 30" Fence Rail System - 14 replies

Need the smaller 30” fence (tube) for the Dewalt 746. Maybe someone upgraded to the longer 52” fence and has saved the 30”. http://www.dewalt.com/partners/flash/dw746/dewalt/dw746.html, http://shopping.yahoo.com/1821175-dewalt-dw7468-30-inch-table-saw-fence-rail-system/;_ylt=A0oG7h2ly.RSrC4Ald9XNyoA;_ylu=X3oDMTEzdDZ0NDFkB...

12-15-2013 03:19 PM

Looking for large roundover Shaper Cutter - 4 replies

Found this on the inter-web.http://toolsandmore.us/roman-carbide-dc2214-shaper-cutters.aspxThis would work if it was Left to Right feed, and might just work with it if there are not any other options [ this large at this low price]. Will not be running 100s of feet, really just want the bell shape profile for small projects. Any thoughts?

12-13-2013 09:03 PM

Pony 56 2-1/2" Deep Reach Clamp - 0 replies

I saw these on the TV the other day….Looks like a much better design the super short ones. http://www.amazon.com/56-Reach-Clamp-Spreader-Fixture/dp/B0000DD1QW/ref=sr_1_3?ie=UTF8&qid=1386968285&sr=8-3&keywords=3%2F4%22+pipe+clamp Any drawbacks? Does the pipe bow and distort the surface they are clamping? AND/OR pop off?

11-22-2013 02:59 PM

Sliding Miter Saws? - 38 replies

Lots of Sliding Miter Saws out there and can’t decide what to buy? This Milwaukee is nice, but expensive and 12” blade, which may be more than I need. http://www.amazon.com/Milwaukee-6955-20-12-Inch-Sliding-Digital/dp/B001BBTZY4/ref=sr_1_1?s=hi&ie=UTF8&qid=1385114692&sr=1-1&keywords=milwaukee+miter+saw Maybe ...


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com