LumberJocks

BigD1's Blog Archive

  • Advertise with us
This blog is written by BigD1 | 25 entries so far
  • Tung oil finish - 11-30-2015 01:34 AM | 4 comments

    Could use some insight on the best way to apply Tung Oil. I’ve read cut the first coat 50-5...

  • Wooden Compass - 09-26-2015 04:44 AM | 5 comments

    Who could tell where I can purchase a Large Wooden Compass for six foot circles. The only one I c...

  • Glueing Ebony wood - 09-23-2015 04:33 PM | 2 comments

    Hello woodworkers. What is the best way to glue Gabon Ebony. How do you prep the wood, and what g...

  • Vicmark 120 chuck - 07-11-2015 03:48 AM | 0 comments

    Can someone tell me, where I can purchase a Pin Jaw, Extended Dovetail Jaw, Spindle Jaw, etc. for...

  • turning redwood logs on a lathe - 05-28-2015 12:13 AM | 3 comments

    I need a memory boost. I watched a video of a gentleman from Ireland, who turns Redwood Logs on a...

  • Finish for Redwood Burl - 02-14-2015 06:16 PM | 1 comment

    I could use some insight for a finish on Redwood Burl. Thanks

  • Sanding Redwood - 02-08-2015 01:26 AM | 3 comments

    I find that 600 grit and 0000 steel wool, both leave sanding lines in my Redwood Burl bowl on the...

  • Natural bark on a Redwood Vessel - 02-07-2015 08:59 PM | 1 comment

    I watched a video where the master turner used a spray finish like a varnish, I believe, to hold ...

  • Sanding Walnut - 07-04-2014 01:10 PM | 7 comments

    Hello fellow woodworkers. How in the world of GOD’S Walnut wood, do I remove hair line, so ...

  • Omni 24 Jig - 03-23-2012 04:57 AM | 1 comment

    I would like to purchase the Omni 24 Jig for dove tails. I would even purchase a used one, if the...

  • New Oneway Lathe - 03-23-2012 04:49 AM | 3 comments

    I just bought a new Oneway 2436 lathe from a private party. The lathe was bought in 2010 and was ...

  • Dove Tail jig - 02-25-2012 04:11 AM | 3 comments

    I am in the market for a dove tail jig that I can joint 20 inch box sides and ends together. I ha...

  • Barrel Nuts... - 12-24-2011 09:34 AM | 4 comments

    I have purchased from Lee Valley, the Barrel Nut and Bolt combo, that is used for work bench asse...

  • Wood prep paste - 05-06-2011 05:20 AM | 5 comments

    Back in 1968, while I was in high school, we had a Paste or Gel we spread on wood, such as Mahoga...

  • Used Wood Lathe - 02-10-2011 02:41 AM | 0 comments

    Hello wood workers. I’m looking for that “Diamond” in the ruff. That would be a...

  • Spindel Sander - 02-01-2011 08:41 PM | 3 comments

    Hello friends. Is there someone who can give me a heads up on the Grizzly Model G1071 Oscillating...

  • finish over oil - 01-30-2011 05:49 PM | 5 comments

    I’m looking for the best top of finish to put over Watco Danish Oil. I want to give it a pr...

  • Working Lights - 01-18-2011 05:21 AM | 4 comments

    Hello my friends. I’m at the point of installing new lights in my wood shop. I’m hear...

  • Finish - 01-12-2011 09:11 AM | 4 comments

    Can someone give me a heads up on the finish “Waterlox”. Is it good , bad???

  • Filling a crack in Alder - 01-05-2011 06:49 PM | 7 comments

    I need to fill in some cracks on the ends of an Alder board, that is end grain. One crack is 1/16...

  • Wood finish.... - 01-03-2011 04:55 AM | 8 comments

    Okay folks. Does anyone know of a wood finish that will work in 40 degree temp. in the cold shop?...

  • Filler and finishing products - 12-15-2010 06:50 PM | 1 comment

    I’m looking for a wood filler that I can use in joint cracks between Alder and Popular, tha...

  • Oak or Maple needed. - 04-18-2010 02:21 AM | 0 comments

    Hello to all you lumber jocks. I am in the need of oak or maple 4×4’s or 4×6̵...

  • Political Wood Working?? - 04-01-2010 06:59 AM | 7 comments

    I must say, I wasn’t pleased to see a “Harry Reid.com” ad on your site. I thou...

  • Maple Hardwood - 03-03-2010 04:16 AM | 7 comments

    Hello my fellow dust makers. I am in the market for some 4×4 maple, to make a work bench. An...

View BigD1's profile

BigD1

79 posts in 4593 days


Subscribe to blog entries (RSS)


By subscribing to the RSS feed you will be notified when new entries are posted on this blog.


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com