LumberJocks

BalsaWood's Forum Topics

  • Advertise with us
View BalsaWood's:homeworkshopprojects (0)blog (0)reviews (0)forum topics (42)buddies (0)favorites (0)activity logWatch
05-24-2017 05:52 PM

Bookcase header and footer movement - 1 reply

When building bookcase with a toekick (footer) or header, is it necessary to allow for movement? The toekick I am looking to put is about 4 inches wide and is solid wood.

05-24-2017 05:49 PM

Dubuque Clamp Works bar clamps - 1 reply

I was browsing around for some new bar clamps and noticed that the “Adjustable Clamp Company” is no more so pretty much no more Pony or Jorgensen clamps. I’ve been looking for clamps made in the USA and found only one company- Dubuque Clamp Works: https://www.toolsforworkingwood.com/store/item/MS-ABAR.XX/Universal_Bar_Clamp...

05-08-2017 05:29 PM

Chances of my piece blowing up? - 9 replies

I made a solid cherry night stand using dados. I also added in a solid cherry back to it which might be a problem. The solid backing is a glue up made using 1/4 thick cherry and is about 22” wide and 2 feet high. I installed the solid backing into a rabbet that runs across the shelves and sides using glue and 23 gauge pins. This was al...

04-27-2017 07:25 PM

Resawing on bandsaws - 7 replies

How much of a difference would there be for a 14 inch bandsaw with riser block vs a 17 inch bandsaw for resawing boards? Im looking at the Grizzly G0555 and the Grizzly G0513 and am debating which to purchase. Im guessing resawing 12 inch boards will happen only once in a while; the majority of boards will be around 6 inches or less.

11-04-2016 08:34 PM

Best plane for highly figured woods? - 18 replies

I’ve been working with highly figured woods and have always experienced tear out of some sort either from the jointer, planer, and jack plane. Even with light passes, tear out sometimes occurs. I’ve been looking at various planes to deal with the tear out- namely: LN No. 85 scraper planeLV low angle smoother with a 50 degree bla...

09-30-2015 07:02 PM

Need help deciding between jack planes - 56 replies

I currently do not own a jack plane and I’m looking to buy one. I am having a tough time deciding between two: Stanley No. 5 type 18 in good condition for 50 dollarsor Lee Valley low angle jack plane for 250 dollars I’m wondering if the LV low angle jack is worth the extra 200 dollars. Any opinions?

09-30-2015 07:36 AM

Hand plane for table top glue ups - 5 replies

I am making an oak table top. I glued up some oak boards and one of the boards ended up slightly higher on one end. I was thinking of some of my options for leveling the board. I don’t have much experience with hand planes so was wondering which hand plane would be good for flattening the table top glue up?

09-14-2015 10:58 PM

Satin to matte finish - 4 replies

I just finished a bookshelf with a few coats of satin Arm R Seal. I’d like to dull it down a little bit and give it less sheen. What would be the best way to do this?

06-25-2015 05:55 PM

Upgrade to Delta T2 fence? - 1 reply

I have a Delta 36-650 with the standard rip fence that came with it. How good of an upgrade would a Delta T2 fence be?

06-24-2015 08:05 AM

Need help selecting a chisel plane or flush trim plane - 4 replies

I need help selecting a plane for the purpose of flush trimming, removing glue, etc…. The two I found are these: http://www.woodcraft.com/product/151301/woodriver-small-chisel-plane.aspx http://www.leevalley.com/US/wood/page.aspx?p=32664&cat=1,41182,48945&ap=1 Which would be better?

06-12-2015 03:45 AM

Using screws along with joinery - 9 replies

I have pretty much used joints and glue for aprons but was wondering would adding screws help reinforce the joinery or be of any help?

06-12-2015 03:20 AM

Glue over finish? - 3 replies

Will wood glue work over Danish oil? I did a poor job of taping one of the mortise and tenon joints and a load of Danish oil went inside the mortise. Some also got on the tenon.

06-10-2015 07:04 PM

Best finish for tabletop made out of imported wood - 4 replies

What would be the best finish for a kitchen table made out of Santos Mahogany? I would like the grain to “pop” but also need it to be very durable. A satin to semi-gloss look would be another requirement.

06-07-2015 06:24 AM

Very bad burn marks with new blade - 20 replies

I just purchased an Infinity Super General blade: http://www.infinitytools.com/10-Super-General-Saw-Blade-40T-5_8-Arbor-125-Kerf/productinfo/010-044/ It is being used with a 1.5hp Delta contractors table saw. While ripping 5/4 oak, I am getting horrible burn marks. I even get some slight burn marks while cutting 3/4 plywood. I switched b...

05-03-2015 08:35 PM

Table saw opinion - 7 replies

I have been looking at table saws for a while and am planning to get one. I’ve been using a circ saw and miter saw for most cuts. Browsing through Craiglist, would this be a good buy for a first table saw: http://chicago.craigslist.org/nwc/tls/5007870345.html My budget is 200 and under for a table saw.

05-01-2015 10:53 PM

Need opinion on jointer I am looking to buy - 18 replies

Looking to purchase this jointer. Any opinions? How about the price? https://chicago.craigslist.org/nwc/tls/4988979720.html Thanks

04-30-2015 07:44 PM

Delta 36-650 - 5 replies

Does anyone have this tablesaw- I am looking to purchase a used one for 200 dollars- is it worth it? Thanks

04-27-2015 01:06 AM

Cheap jointer suggestions - 1 reply

Anyone have any experience with a Wolcraft 611 jointer? http://chicago.craigslist.org/nwc/tls/4992408959.html I’m looking for a cheap jointer and came across what is listed in that link. Around 100 dollars is what I am willing to spend on a jointer since I will be looking for a decent planer as well.

04-07-2015 05:54 PM

Budget table saw - 23 replies

Can anyone recommend a decent and safe tablesaw for around 100 dollars- I’ll be looking through craigslist for the item.

03-30-2015 07:38 AM

Screw reinforcement - 4 replies

For the bookcase I am working on, I have created dados for the shelves. I will also have some 1/4 plywood for backsplash. I am using 3/4 oak for the rest of it; shelves will be about 26 inches long and 11 inches wide. Would it help reinforce the shelves if I screwed the backsplash to the shelves from the back of the bookcase? I have seen peo...

« prev 1 2 3 next »
42 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com