LumberJocks

3285jeff's Forum Topics

  • Advertise with us
View 3285jeff's:homeworkshopprojects (0)blog (1)reviews (0)forum topics (127)buddies (1)favorites (1)activity logWatch
06-10-2020 11:18 PM

router pin - 5 replies

can anyone tell me where to get a replacement router pin for the jessum router 02310,,i lost the one that came with the router lift and i tried jessum,,,and its not really that bad to replace it,,4.99,,but the shipping and handling it 15.00,,,i thought about making my own,,but i dont know the thread size,,,any help would be appreciated,,

05-03-2020 11:58 AM

router depth - 5 replies

i have the bosch 1617evs and it being a great router,,,do they make a router that has more depth when you adjust it,,i was looking for one that you have a longer adjustment arm

03-29-2020 02:35 AM

tear out using dado blades - 22 replies

this might seem like a silly question,,,but I just bought some dado blades and was planning on dadoing some shelves across plywood,,and this is my first attempt at it and it splintered really bad,,,the blades I have are not cheap,,i bought them from amazon and they had a good rating,,and I paid 90.00 for them,,,but the crosscut across plwood was...

03-06-2020 03:40 PM

countertop - 9 replies

I am making a countertop for my son and I glued 2 sheets of 3/4 plywood together…I have been watching alot of you tube videos…this is my first experience with formica so I thought I would ask for your input also..should I put the edge banding on first..which I am going to cut from the piece of formica I have…what would you reco...

03-02-2020 03:47 PM

aftermarket blade guard - 3 replies

I have the delta 36-725 table saw that lowes sells,,,and prior to that I had the dewalt 7491rs table saw ,,,my question is this,,,on the dewalt the guard and riving knife were all one piece,,,in other words when you wanted to remove it you just pulled a lever and everything the guard and riving knife pulled out,,the delta on the other hand to re...

02-13-2020 12:01 AM

looking for a good palm router - 14 replies

i have been looking for a good palm router and i wanted the plunge base with it also,,i found one on amazon,,its called a mophorn which i have never heard of before,,but it does come with alot of attachments including the plunge base and the reviews werent all that bad,,,i was just wandering if anyone knows anything about this router and could g...

01-24-2020 11:29 PM

router bit height - 9 replies

I know this might seem like a crazy question but I have the bosch evs1617 router mounted on a bosch router table,,and I cant seem to get the bit to raise high enough,,,,unless of course I raise it out of the collet a lot which is dangerous,,i have got the twist knob raised as high as as I can get it and even took the router out of the housing an...

12-30-2019 04:41 PM

Dado shims - 4 replies

Has anyone ever used the dado shims that lee valley sells…they have cutouts on the side to slide on your arbor shaft…seems like they would be easier to get on and off rather than the conviental type…

12-28-2019 03:48 PM

dado blades - 7 replies

I just bought a dado blade set and going by the directions for a 3/4 dado it said for me to use the inside and outside blade and 4 of the 1/8 chippers,,which I did and it does cut a 3/4 groove but its not as tight as I like it to be,,im really new at using the dado blades,,so if anyone can help me get a tighter fit I really would appreciate it,,...

11-20-2019 09:36 PM

craftsman 10 inch bandsaw - 4 replies

does anyone know if there is any upgrades you can make to a 10 inch bandsaw,,I checked with carters and they don’t have any,,it would be nice if there was so you could change blades more quickly,,,,thank you

10-31-2019 09:23 PM

vacuum chucking - 3 replies

can anyone tell how would you mount the piece back to the vacuum chuck if you didn’t have a foot on the bottom to aligned with the vacuum chuck for it to run true

09-25-2019 02:33 PM

grizzly - 5 replies

I bought this saw and im sure all the saws they sell has this issue,,if the saw is unplugged and you go to plug it up it will come on,,,in other words if the power is intruped ,,,the saw will come back on when power comes on,,,and I called grizzly hoping to get a replacement switch,,which is a magnetic switch,,the person that I spoke with in tec...

09-19-2019 04:44 PM

Sphere jigs - 16 replies

I have been thinking about investing in a sphere cutting jig…the one by chefware kits or carters jig..can anyone tell me which is the better of the two and which one is the easiest to set up…I know carter is way more expensive than the chefware jig…any info would help…

09-15-2019 12:47 PM

extension cord for table saw - 9 replies

I just purchased a grizzly go833p table saw which is 220,,,i have 220 but the cord from the table saw is short and I was thinking about making a 10 foot extension cord for it,,,would this be acceptable for the saw,,im sure 12/3 would be the correct size for the wire,,,its not pulling but about 8 amps,,,my question is would it be a loss of power...

09-01-2019 10:19 PM

Need help deciding on new table saw - 5 replies

I sold my dewalt dwe7491rs which was a great saw very accurate and it actually suited my needs ..except I wanted a larger table..I have looked at the delta at lowes..36-725 I believe is the model number.but I have heard that customer service is horrible…so I have gotten it down to 2…the grizzly go771z or the go833p….I have 220 ...

03-12-2019 01:03 AM

help with bandsaw - 4 replies

im looking at getting a larger bandsaw,,at the moment all I have is a benchtop,,I have been looking at the rikon 10-326 and the grizzly go513xp and the go513 anniversary edition,,,and the laguna 14bx,,,i know the grizzlys just have a one year warranty where rikon has 5,,dont know about laguna,,,I like the grizzlys but I guess im hungup on that f...

12-20-2018 10:55 PM

sphere jig - 2 replies

I have been wanting a sphere cutting jig to turn round balls,,i have checked different ones and needless to say none of them are made for the weekend woodturner,,,,price wise,,but I have thought about trying to build one,,does anyone have any info on building one,,,i have been watching you tube but I didn’t know if anyone could add to it ,...

11-18-2018 11:44 PM

choosing a table saw - 11 replies

im looking for a table saw and I wanted to get some advice on which one that others prefer,,i have narrowed it down to the grizzly g0883p or the g01023rl which both are on sale now,,both come with a 1 year warranty or the jet 725000k which has a 5 yr warranty and Woodcraft is giving 15 percent off now,,,any help would be appreciated,,,,thank you

11-12-2018 01:37 AM

looking for a scrapper - 6 replies

I have been looking for a 1/4 round nose scrapper,,i know sorbys sells one but everywhere I look it seem like they are out of stock,,,can anyone help me find one,,,it don’t have to be a sorbys,,,,,

10-29-2018 02:25 AM

texturing tools - 2 replies

thinking about getting a texturing tool but I have seen several different brands,,can anyone point me in the right direction on which one they prefer and why,,,thank you

1 2 3 4 ... 7 next »
127 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com